y1416/03 GPM - Ultragrip/MadMax Big Digger combo with HPI rims for HPI, Losi, Carson and Co. (24 mm hex) 2 pairs
€109.80
Available
Product information "y1416/03 GPM - Ultragrip/MadMax Big Digger combo with HPI rims for HPI, Losi, Carson and Co. (24 mm hex) 2 pairs"
Front tires
150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire.
The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel!
This makes the car less prone to unwanted traction rolls!
Due to the extreme load created by the GPM Ultragrip tires the rim was optimized again with a reinforcement ring.
The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars.
The GPM Ultragrip are designed for use on sandy surfaces.
We recommend to check the beadlock screws after the run.
Dimensions:
- Outer diameter: 170 mm
- Front tire width: 60 mm
- Reinforced 24 mm hexagon wheel drive
Rear tires
BIG DIGGER 170x60 with black HPI rims, 20-fold bolted, with 24 mm hexagonal mount and reinforced orange rim rings for Losi, HPI, Carson and many more.
Due to the extreme stress caused by the MadMax BIG DIGGER tyres, the rim has been further optimised with a reinforcement ring.
The MadMax tyres have 84 extremely strong lugs, each measuring more than 1 cm² and 6 mm high, which enable optimum power transmission and provide excellent grip even on loose surfaces such as sand and earth.
The tyres are equipped with a special rigid tyre insert that transfers the applied force without tilting, even on heavier models.
We recommend checking the screw connections on the rims after use.
Dimensions: Outer diameter: 170 mm Tyre width: 60 mm Reinforced 26 mm hexagonal rim mount
- 2 pairs
Login
Customers also viewed
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!
These protective covers prevent the shock piston rods and seals for wear caused by dirt. They fit most 1/6 and 1/5 scale shocks.Not suitable for Gas Devil, Thunderbolt, Helldevil, CRT 4x4!- total length 150 mm for all FG / Carson / Smartech / Conrad and all dampers with a diameter from 22 to 30 mm. Set of 4
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 3 mm allen head screws (for 2,5 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece
MadMax MAXI PIN tyres have been specially developed for carpet race tracks! The special block tread pattern, with 480 knobs per tyre, provides excellent grip, but also puts extreme strain on the tyre and the rim. The 3-piece Super Star rims from HPI ensure that the tyre fits perfectly on the rim. This means that no adhesive is required to fix the tyre in place and the rim can be used again and again with new tyres. To stabilise the tyre, the outside of the tyre shoulder is equipped with vertical ribbing on the side, which minimises tilting under load and counteracts the shear forces that occur in bends. Furthermore, the MAXI PIN tyres have knobs positioned on the side of the outer side, which particularly support the steering behaviour of your RC car in bends. Taken together, the MAXI PIN tyres provide maximum grip. The set comes with inserts and orange rim rings, including screws. On request, we can fit the tyres for an additional charge; see the options above. Dimensions tyres : - Outer diameter: 185 mm - Tyre width at the outer edge of the tread: 75 mm Dimensions rims :- Outer diameter: 120 mm- with: 60 mm 1 pair - Outer diameter: 185 mm - Tyre width at the outer edge of the tread: 75 mm 1 pair
Genuine HPI spare/option part. Content:1 set