y1396/32 Reed valve piston

rc-car-online

€49.90*

Prices incl. VAT plus shipping costs

Currently unavailable

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Product number: y1396

EAN: 4058575060727

Product information "y1396/32 Reed valve piston"

Genuine Zenoah piston with machined recess for use with Are reed valve block BJ035.

Please note:
Differing widths of the remaining webs of the piston skirt are caused by production spread of the pistons.

Version:

y1396/32 - Zenoah G320

Content:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also viewed

AREA-BJ035/05 Replace Epoxy plate for BJ035

Genuine Area RC spare/option part. Spare sealings for Area reed valve system BJ035 till 29 cm³.Contents:1 piece

€24.90*

ST0010 SPEED TEC weight-reduced balanced tuning flywheel

Genuine Speed-Tec spare/option part. SPEED TEC tuning flywheel for Zenoah G230/240/260/270/290/320 and Chung Yang engines (includes HPI Fuelie and Losi).The weight reduced (210 vs. 230 grams) flywheel enables the engine to accelerate faster and rev higher. The optimal balancing guarantees better endurance at lower fuel consumption!A durability approval exists!Contents:1 piece

€99.90*

AREA-BJ047 Reed valve block V2 for Zenoah G320

This reed valve system converts a normal piston-port engine into a reed valve engine. It offers the advantage of increased intake duration for a better charge for more power. As a positive side effect no fresh gas loss occurs during the downward movement of the piston because the membranes close this path.The reed valve block replaces the usual stock insulator. To use the advantage of the reed system, it is necessary to modify the piston skirt on the intake side. Depending on the engine it is advantageous for best results, to slightly match the cylinders intake port to the Epoxy insulator plate at the bottom of the reed valve system. Both steps are described in the installation instructions for Zenoah and Chung Yang engines. Our thanks for these instructions go to our customer Thomas Hoenicke.Note: For the time being the epoxy insulator plate must be slightly reworked to fit a G320 Zenoah engine. The manual has been written with the conversion of a G320, the affected area for modification is therefore shown.The unit is 24.5 mm high.

€79.90*

y1016/051 Carburetor WT1107 G320RC

Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.

€79.90*

y1009 Zenoah G240RC with Walbro carburetor WT 990

23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€274.90*

y1312 Twin hose bracket

Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €14.90*

Details

Tourex TXLS817 Big Speed 2 Clutch carrier On-Road/Off-Road

Genuine Toruex spare/option part.

€39.90*