Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece
Genuine Losi spare/option part. Genuine Instruction Manual.Printed instruction manual as included with every model.Languages:GermanEnglishFrenchItalianContents:1 piece
Genuine FG spare/option part. The body shell is delivered unpainted, without decal set and rear wing.500 mm wheelbaseLength: 690 mmWidth: 385 mmHeight: 240 mmContents:1 piecePainting tips:
hurrax_racereifen Version:
HX0400 extreme grip Medium 175/70 mm
HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mm HURRAX extreme tires are available in soft (blue marker!) and medium through our shop menu.Contents:2 pieces tires2 pieces inlays
You can select the tyre hardness above: - Hurrax HX100 extreme Grip Medium 175/70 mm tyre
and - Hurrax HX400 extreme Grip Soft 175/70 mm tyre Please select which tyre you prefer. You also have the option of having the tyres delivered ready glued for an additional charge. Please click if you want to have the tyres ready glued!
HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Alternative: y2002 Alloy a-arm, front upper FG 4WD - Fits FG Leopard 4WD und Sportsline onroad 4WD with 510mm wheelbase.Does not fit FG Leopard 2WD und Sportsline onroad 4WD with 530mm wheelbase.
The Wheelbase of the WB535 2WD version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ Zenoah engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models.The body shell comes unpainted, a decal set with writings for further decoration is enclosed in the delivery.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURAlloy spur gear carrierUse for 48T - 46 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 15The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 217,30 EURThe pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm
The Wheelbase of the WB535 version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models.The body shell comes yellow. A decal set with writings for further decoration is enclosed in the delivery.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm
Item N° y0961/02 FG manuals for Monster/Stadium Competition 4WD, 1 St.Genuine FG manuals as included with the cars.
€3.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).