Genuine Losi spare/option part. Genuine Instruction Manual.Printed instruction manual as included with every model.Languages:GermanEnglishFrenchItalianContents:1 piece
Genuine FG spare/option part. Suitable on the front axle for all FG 1:6 buggy models.Dimensions:Mounting hole distance: 113 mmTravel: 26 mmDiameter: 20 mmFG factory fill is viscosity 2000 for Marder & Co. and 1000 for stadium / monster cars.RecommendationMarder & Co.: during winter viscosity 1000 - 1500, 1500 - 2000 for summerMonster / Stadium: For offroad use in the winter viscosity 700 - 900, for summer 900 - 1500; use a slightly higher viscosity for on-road useContents:1 piece
Former: "Atego" Truck.The Sportsline 08 quality at a reasonable price for beginners. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 20T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. The models are equipped with a powerful 23 cm³ combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURDimensions:Length: 880 mmWidth: 435 mmHeight: 380 mmWheelbase: 530 mmTrucks in action!
The legendary sports car Bugatti EB 110 body shell for 1:5 on-road cars with standard chassis width and 530/535 mm wheelbase. The body shell is vac-formed from 2 mm Lexan.Dimensions:Total length approx. 870 mmTotal width approx. 380/385 mmTotal height approx. 220 mmRequired body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7154/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts The body support FG 7154/01 is screwed directly onto the rear bridge. For attachment to the rear bridge, 2 holes 4 mm must be drilled in them.As a detailing kit (mirrors, windshield wipers!) set # 5435 is recommended (not included!).Since the Bugatti EB 110 1:5 scale body is - just like the original very low, a very low height air filter (#9043) is required. We also recommend 9.5 mm wide wheel squares: #6107 wheel squares 9.5 mm/M6 - 2pcs..For the body side support 32781.
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).