y0563 Alloy front shock tower for 4WD FG-Monster/Stadiuim/Beetle Leopard cars

€79.90*

Available

Product number: y0563

EAN: 4058575030737

Product information "y0563 Alloy front shock tower for 4WD FG-Monster/Stadiuim/Beetle Leopard cars"

Genuine HT spare/option part.

Milled to reduce weight; replaces plastic part FG #66287/01. Comes complete with all necessary mounting hardware included.

Fits Leopard Sportsline 2WD and 4WD.

Scope of delivery:

1x Alloy front shock tower
4x Socket head cap screws 4x14
3x Countersunk screws 4x14
4x Washers steel 4,3

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

AR-023 Fuel line hose clamps

For a secure fit of the fuel line. The self-adjusting clamps are suitable for diameters from 6 to 7 mm.Contents:10 pieces

€8.90*

y1380 High performance starter rope, carbon grey

3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.

€8.90*

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.

Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

€89.90*

y7087/02 Alloy shock shaft end long

Genuine HT spare/option part.Replaces FG 7087/02.Fits all FG shocks, Carson 2WD and many other 1/5 and 1/6 scale models. There are replaceable bushings.Dimensions:Length overall: 27 mm, about 22 mm to to center of bushingThread for shock shaft: M4Bushing inner diameter: 4 mmContents:2 pieces

€15.90*

Similar products

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1036 HT rose joints with conical spacers

Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers

€18.90*

y0321 Off-Road tuning springs Dirt-Spring M

federn_dirt_m Version: y0323/06 - M16, black

Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces

€17.90*

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

GPM 66275 Universal drive shaft with ball drive conversion kit for most FG 4WD cars

FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218

€159.90*

Details

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

€17.45*

y2002 Alloy a-arm, front upper FG 4WD/Leopard 2WD

Genuine HT spare/option part.Alloy a-arm front upper for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster-/ Stadium- Modelle 4WD RTR, 4WD Porsche and Mini. Replacement for FG item No.: 66266Contents:1 piece

€34.90*

y0578, Alloy front shock tower for FG Sportsline and Off-Road 4WD, 1 pce.

Aluminum front shock tower for FG Off-Road Buggy and Sportsline 4WD, replaces stock plastic part FG #66287.Stock mounting hardware will be re-used.

€59.90*

68415 FG Cardan joints for front axle 4WD

Genuine FG spare/option part.With M8 thread!The set contents 2 cardan joints, ball diff. axles, protective bellows, balls.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/ Stadium models 4WD RTR.Contents:1 set

€138.50*

68411 FG Front lower alloy wishbones 4WD

Genuine FG spare/option part. Set contents front lower wishbones, rose joints, screws.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/ Stadium models 4WD RTR; on-road cars with 510 mm wheelbase only, i.e. 4WD Porsche and Mini.Contents:2 pieces

€137.50*

y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

€16.45*

Customers also viewed

13401/13402 Lower front a-arms front for FG Marder, FG Buggy with rose joints a.s.o.

Lower front a-arms for all cars of the Marder family. Made from high quality aluminum, the arms are light weight, stiff and durable. They feature plastic bushings for the hinge pin and come with the required set of rose joint and conical spacer inluded.Contents:1x L/h a-arm with hardware1x R/h a-arm with hardware2x Rose joints4x Conical spacers

€129.90*

y0897 Wheelie bar with suspension for 2WD + 4WD models - 1pce.

€89.90*

7452 FG 2-speed gear box 1:5 4WD for Sportsline 4WD, set

Genuine FG spare/option part.Fits FG cars with 510 mm and 535 mm wheelbase. Not suitable for Competition and Formular 1 models.Included gears:1st gear: 22T / 42T2nd gear: 24T / 40T2-speed gear box, retrofitting is possible for all FG 1:5 Sportsline 4WD models. Adjustable shit point, built very robustly, therefore high reliability gearwheels can be replaced in not time. The small gearwheels are made of hardened steel. If you use the gearwheel 7424/01 (38 teeth) you need the allow hub A 47 mm 7456/01.

€244.95*

7456 FG Alloy hub A 52mm - 1pce.

Item N° 7456 Alloy hub A 52mm - 1pce.Suitable for gear wheels with 42 or 44 teeth in connection with the 2-speed gears or .

€35.90*

Elcon 14404, front shock tower for FG Monster Truck 2WD

CNC-milled aluminum version, suitable for the old version of the FG 2WD monster and stadium models. These vehicles were distinguished by coming from the factory with four shocks each front and rear. The shock tower comes complete with mounting hardware and four quick-release mounts for the upper shock ends.

€79.90*

6099/01 FG Front shock mount for Monster-Truck

Genuine FG spare/option part. Suitable for all FG Monster-Truck und MB-Pro models.Dimensions:Height: 92 mmWidth: 160 mmContents:1 piece

€17.90*

y2003 Tuning front suspension set for nearly all FG 4WD Sportsline cars

y2003 Model: y2003/01 - FG 4WD Monster-Truck models, Beetle+ 40EUR

Tuning front suspension set for all FG 4WD Sportsline cars: Monstertruck; Baja; Marder; Beetle; touring cars:Not fit Formular 1, Leopard and Truggy!y2003/01 fits:FG 4WD Monster-Truck models, Beetle.Part number:Name:y68412Aluminum front lower a-armsy2000Alu Querlenker Front unteny68413Aluminum front uprightsy0563Aluminum shock tower Monster-Truck/Beetley1036Rose joint for alloy wishboney2003/02 fits: FG 4WD Baja Buggy.Part number:Name:y68412Aluminum front upper a-armsy2000Aluminum front lower a-armsy68413Aluminum front uprightsy0578Aluminum shock absorber plate for Bajay1036Rose joint for alloy wishboney0579Alloy roll cage brackety2003/03 fits:FG 4WD Marder and FG touring cars with 510 mm wheelbase: Mini Cooper and Porsche GT3 RSR. When installing in a Porsche GT3 RSR or Mini Cooper 4WD with 510 mm wheelbase, the steering travel limiter must be installed into the first threaded hole of the knuckle arm and not at the standard location on the knuckle as in off-road cars!Part number:Name:y68412Aluminum front upper a-armsy2000Aluminum front lower a-armsy68413Aluminum front uprightsy0578Aluminum shock absorber plate for Bajay1036Rose joint for alloy wishbone

Variants from €469.90*

€509.90*