Genuine Zenoah piston with machined recess for use with Are reed valve block BJ035. Please note: Differing widths of the remaining webs of the piston skirt are caused by production spread of the pistons.Version:y1396/29 - Zenoah G290y1396/32 - Zenoah G320Content:1 piece
The ideal cleaner for pretreatment of Lexan body shells when are to be applied! Decals or detailing kits will stick significantly better to a body shell cleaned with LOCTITE 7063. Also great for removal of "battle scars" from the body shell. But note: The cleaner should not come in contact with the printed surface of the decals!Use to prepare surfaces to be bonded. The product flashes off very quickly and it allows cleaning directly prior to adhesive/sealant application. It is non-corrosive and non toxic.Application:Spray a sufficient amount of product on the surface to be cleaned and wipe while still wet to ensure heavy contamination and excess solvent is removed.Content:400 ml
Genuine HT spare/option part. Fits Area 5ive-T rear uprights AREA-5T-034 on the driveshaft side. Both sides sealed (2RS) for increased dirt resistance. Does not fit stock parts! Content:2 pieces
The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece
Full set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket
Genuine Speed-Tec spare/option part. Complete set of SPEED TEC Drag seals for smoother running of the crankshaft and therefore higher final engine speed, as well as low-drag rev up of the engine.Therefore a bit more performance on the complete rev band and by the use of crankshaft bearing with high-strength steel balls and qualitatively high-class oil seals more safety and stability, even on tuned engines.Content:two pieces Drag sealstwo pieces crankshaft bearing with high-strength steel balls for higher lifetimetwo pieces high-class oil seals (shore hardness 15)It is recommended to use a drop of oil or grease for the installation therewith the bushings won't jam.Contents:1 set
Genuine Zenoah spare/option part.Great comfort, natural heat regulation. White with black/red edging on collar and sleeves and grey logo imprint.Machine washable for easy care!Size:L - LargeContents:1 piece
These cask shaped springs are especially designed to fit the diameters of Mecatech Klick-Shocks and Mecatech Big Bore shocks.Dimensions:Inner diameter, upper: 20,5 mmInner diameter, lower: 16,5 mmOutside diameter: 29,5 mmLength: 49,5 mmWire diameter: 2,8 mm
Genuine INNOTEC spare/option part. The RC-car all-round wellbeing set for cleaning, sealing and moisture displacement. Set contents: INNOTEC PE100 silicone spray for plastic and rubber care PE100 was specially developed to protect plastics from external agents. The product penetrates right into the molecular structure of the plastic, which is thus protected from the inside out, remains permanently supple and retains its natural gloss. Content 500 ml Can INNOTEC Multi Spray 1000, moisture displacing lubricant Multi Spray 1000 is a strong moisture displacing lubricant that loosens stuck parts and protects against corrosion. Multi Spray 1000 displaces moisture by penetrating between the substrate and water and then protecting the substrate like a protective film. The product is ideal for numerous applications in the RC hobby. Content 500 ml Can INNOTEC Adhesive remover and degreaser Seal and Bond Remover is a slow evaporating universal degreaser that is also perfect for quickly and efficiently removing all types of adhesive and sealant residue. The product softens most adhesives and sealants to make them easier to remove. Content 500 ml Can INNOTEC Power Clean Metall- und insbesondere Aluminium Reiniger Power Clean ist ein sicherer, schnell wirkender Reiniger/Entfetter für fast alle Arten verunreinigter Metallteile und -flächen. Das Produkt entfernt Bremsstaub, Teer, Unterbodenschutz, Fett und diverse Wachse und jede Art von Verschmutzung. Power Clean ist ein ungefährlicher Reiniger für elektronische Brems- und ABS-Systeme. Da das Produkt den Untergrund nicht angreift, eignet es sich auch besonders zum Entfernen von Teerspritzern sowie Fettund Ölflecken. Content 500 ml Can INNOTEC Multi Clean Universal foam cleaner for all plastic and metal parts on the RC car Multi Clean is a highly effective foam cleaner for countless types of dirt on almost all surfaces that can be easily applied to horizontal as well as vertical surfaces due to a stable active foam while intensively affecting the contaminants. Content 600 ml Can Set consists of:5 Dosen
Genuine Speed-Tec spare/option part. When the SPEED TEC Drag seals complete set y1369 is mounted, it is possible to exchange the Drag Seals rings without disassembling the crankshaft.Content:two pieces Drag sealsIt is recommended to use a drop of oil or grease for the installation therewith the bushings won't jam.Contents:2 pieces
TURBO-TWIST, 325 mm long screw driver in top quality.Allows easy access to hard-to-reach screws in any 1/5 & 1/6 car.Features:Soft Grip handlesExtra long 325 mm shaftChrome Vanadium hardened and tempered bladesBlackened magnetic tipsVersions:y1366/01 - Phillips No. 0 / PH0y1366/02 - Phillips No. 1 / PH1y1366/03 - Phillips No. 2 / PH2y1366/04 - Flat 1.2 x 8 x 325 mm
Genuine SCZ spare/option part. CNC-machined 6061-T6 aluminum engine mount for the SCZ 290E, required for installation in the Losi DBXL.Contents:1 piece
Genuine HT spare/option part.Affectionately custom-made hand-sewn overalls suitable for the H.A.R.M Kart RK-1. It is tailor-made and can be exchanged directly against the stock overalls.Available in three different color combinations: y1496/01 - yellowy1496 / 02 - blue y1496 / 03 - red Contents:1 piece
€99.90*
This website uses cookies to ensure the best experience possible. More information...