70 products found for "y1003"

Catalogue #1

HT Aluminum rear suspension conversion kit for Smartech UNO, Carson Attack / Super Attack / Gas Blaster / C5 / R5, 2WD , y1003, set

Alloy rear axle conversion kit for Smartech UNO and Carson Attack and Super Attack (not Evo!), Gas Blaster and C5; Smartech Spider and Ranger cars.Fits for:- C5 / On road / Touring car- C6 Attack- Touareg- Super Attack- Gas Blaster- Duratrax Firehammer- Spider- Big AttackThe set includes:- rear plate- differential mounts- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075, also you need two packets turnbuckle 40 mm 6100/04.

€299.90*

y1008 CFH gas

Genuine HT spare/option part. Propan/Butan gas mix for the torch above, similar units and cigarette lighters. Contents:1 piece / 100 ml

€3.50*

y1005 Carson clutch bell, ventilated

Holes in the front improve clutch cooling. Additional to the standard e-clip you can now use a screw with washer to secure the pinion. Flat sections for grub screws with 180° offset.

€39.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1007 CFH Diamant M50 gas torch

Genuine HT spare/option part. Powerfull high quality soldering torch with piezo igniter, runs on standard lighter gas. Great for removing bolts that have been installed using thread locking compound. Removable safety base for convenient hands-free operation., adjustable flameTechnical data:Flame temperature: approx. 1.300 °COperating temperature: approx. 650 °CTank capacity: approx. 26 g ButaneConsumption: approx. 20 g/hFlame adjustement: from 12 mm to 32 mmIgnition system: piezo ignition (like electronic lighters)Please note: due to shipment regulations the torch is not filled with gas when delivered!Contents:1 piece

€39.90*

y1009 Zenoah G240RC with Walbro carburetor WT 990

23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€260.80*

y1002 Vehicle decal set Pajero like FG 6217/01

Genuine FG spare/option part. Contains the stickers of the headlights, the rear lights and the radiator grill.Not included are the advertising labels for the original design. Please order separately.Dimensions:410 x 230 mmContents:1 piece

€13.30*

y0003 Billet brake lever, long

Genuine HT spare/option part. Fits HT Baja 5B premium brake and FG offroad models, race truck and Formula 1.Contents:2 pieces

€24.90*

y1303 T-connector charging cable 4mm

Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

y1030 HT Aluminum front bulkhead B for 2WD

Genuine HT spare/option part. Comes with two pairs of special bushings to adjust camber changes during the suspension movement.Fits 1/6 cars like Marder, Monster Models, Pajero, Beetle and many more.Contents:1 piece

€28.90*

y1043 connector straight for hydraulic brakes - 1 pce

connector straight for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.Connecting thread M5

€8.90*

y1013 Motul Air filter oil for foam filters

Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

Content: 400 Milliliter (€47.25* / 1000 Milliliter)

€18.90*

y1203 HS gilmer belt for FG 4WD cars, 1 pce.

Dimensions same as FG 66237.Very high rupture strength and tearing resistance as well as reduced wear make this belt the perfect choicefor race applications where maximum reliability is a must.Fits cars with 490 and 510 mm wheelbase only. Does not fit WB535 cars! For all FG Offroad 4WD models with 490-510mm ( Offroad buggy, monster and stadium) and all FG Sportsline 4WD 510 ( Porsche GT3, Mini and BMW E30 ) leng 635mm, wedth 18mm.

€34.90*

y1603 SPEED TEC CRANK Team-Edition Zenoah G270 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, the intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Cylinder modified for installation of the ignition systemPiston:Transfer port area optimized for flow, weight reduced and the piston-roof is flow-optimized and polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

This product is currently not available.

y1033 HT Aluminum front suspension for FG Marder, Beetle, Pajero, Monster Beetle 2WD, set

The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1032HT Aluminum shock tower Marder 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 391,00 EURThe sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!Fits FG Marder, Beetle, Pajero and Monster Beetle.

€339.00* €391.00* (13.3% saved)

y1000-54 Mecatech brake line, 1 m

Dimensions:Inner diameter: 2 mmOuter diameter: 4 mmContents:1 piece

€4.00*

y1004/01 Driveshaft boots for ball drive and dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt.For FG and Carson ball drives, fits standard dogbones as well.Content10 pieces

€34.90*

y1000-53 Mecatech brake fluid, 50 ml

Replacement part for Mecatech twin piston hydraulic brake.Contents:1 piece / 50 ml

€8.90*

10035/01 FG Upper wishbone F1 for M7

Genuine FG spare/option part. Plastic wishbone with 6mm boring suitable for the reinforced wishbone threaded rods M6.Contents:2 pieces

€17.50*

y1103 Body support

y1103 Size: y1103/01 - Small

Genuine HT spare/option part. You can select from two different sizes of body support.Dimensions small body support y1103/01:Length: approx. 80 mmWidth: approx. 16 mmDistance bore to bore: approx. 64 mmDimensions large body support y1103/02:Length: approx. 105 mmWidth: approx. 16 mmDistance bore to bore: approx. 88 mmBore diameter: approx. 8 mmContents:2 pieces

€7.90*

10030 FG Front axle carrier

Genuine FG spare/option part.Suitable for Formula 1.Contents:1 piece

€19.90*

10031/01 FG Distance bolts - 2pcs.

Suitable for Formula 1.

€7.90*

y0003/01 Pin for Billet brake lever y0003 and y0015

Genuine HT spare/option part. Fits for the brake levers with the numbers y0003 and y0015.Contents:2 pieces

€2.90*

10035 FG Upper / lower wishbone - 2pcs.

Plastic wishbone with 6mm boring suitable for the reinforced wishbone threaded rods M6.

€17.50*