Genuine FG spare/option part.Only suitable for alloy gear flange-engine mount 1040/05.See below for layshaft 10x19x7 mm and clutch bell 10x22x6 mm bearings.Content:1 pieces
Original Losi Ersatz-/Tuningteil.Spare parts for Evo Porsche to get there without any problems with the linkage on the fuel tank. But also a very useful distance bolts of it is because the gas / brake / hydraulic linkage to the servo to insert later. Therefore will make the bending of the linkage in most superfluous.The recommended screw us with the part number 6724/12 available as a link in the lower part of the page for accessories.Contents:1 piece
Genuine FG spare/option part.The damper plate 2011 received further adjustment borings for the shock absorbers. According to a modified set-up the shock absorbers can be mounted much flatter in combination with the rear alum. damper mount. The model therefore has much more cornering grip.Suitable for the Competition 07-510 and 07-530 models as well as for the Competition EVO 08-510 and EVO 08-530 models.Contents:1 piece
Genuine FG spare/option part. Is sheeted in the Evo 04 / 08 in connection with the mechanical disk brake.Only suitable for Evo 04-08 gear plate 1039Content:1 pieces
Genuine FG spare/option part. 4mm ball track for the rear ball stabilizer . Standard equipment on Evo 04 - 08 and Evo 2020 rear axle.Fits a-arms with 5 mm slot only!Ball diameter: 11.5 mmTotal length: 100 mmContents:1 piece
Genuine FG spare/option part. When installing the higher Truck rear axle riser plates, these spacer are needed to compensate for the increased height difference between engine mounts (1063/01 and 1040/05) and rear axle brace 1063.Small spacer: 8 mm hex, 9.1 mm height, 4 mm bore.Large spacer: 10 mm hex, 9.1 mm height, 5 mm bore.You'll need a longer screw (M4x20) for installation of the r/h engine bracket 1063/01.Fits for Evo 04 - 08. Contents:2 pieces
Genuine FG spare/option part. Contains the stickers of the headlights, the rear lights and the radiator grill.Not included are the advertising labels for the original design. Please order separate.Dimensions:470 x 260 mmContents:1 piece
The latest FG EVO alloy chassis with longitudinal grooves at the bottom. This reduces the contact patch of the chassis when touching the ground. The reduced tendency for rubber pickup results in lower loss of speed when the suspension bottoms out.Siince the overall length of the plate was reduced to 670 mm, is needed to install the rear body support. The chassis plate weighs 925 grams.Please note that the rear wing support from all previous EVO cars until 08 cannot be used with this chassis plate.
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
Ready for an extra portion driving fun? Then try the FG Monster Buggy Pro! This aggressive looking model based on the Fun Cross chassis is extremely fast, easy to handle and very pleasant to drive. A complete package of well-tried racing technology! The model will be delivered with a clear body shell.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURPowerful 26 cm³ petrol engineMaintenance friendly chassis2 Differential gearsHardened driving partsCompletely ball-bearingedLarge-volume alum. dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure funThe model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.Measures:Length: 715 mmWidth: 495 mmHeight: 360 mmWheelbase: 535 mmWeight: 10,4 kg