Heavy gauge (14 AWG / 2 mm²) charging cord with EC3 plug and gold plated contacts. Especially for Losi/Horizon rx-batteries which feature an EC3 connector additionally to the regular rx-connector. The EC3 system can candle much higher charging rates which reduces charging time of high capacity battery packs significantly.Dimensions:Length approx. 20 cm
Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 piece
Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Monster- and Stadium rims 6232, 6232/01, 6232/03, 6232/04, 6232/05 and 6232/06.14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 pieces
Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 6105, 6105/01 (white) and 3105 (silver).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 pieces
Genuine HT spare/option part. Schneider permanent marker, cap with clip and bullet tip. Dries quickly, water and wipe proof, black color.Recommended for marking and contour tracing on body shells.Lines can be easily removed with isopropyl alcohol or dry-cleaning naphtha.Contents:1 piecePainting tips:
Genuine HT spare/option part. For easy, precise and equal adjustment of spring tension, fits all 1/5 and 1/6 shocks with a body diameter of 15 - 16 mm.Set with two clips each of 1, 2, 3, 4, 5 und 6 mm thickness.Contents:1 set
Genuine HT spare/option part. Complete seal bearing rate with 24 bearings for the FG Competition 4WD models. Quantity / Size / use:4 pieces 6 x 15 x 5 mm - Front Pulley2 pieces 10 x 22 x 6 mm - Clutch Bell6 pieces 10 x 19 x 7 mm - layshaft / belt tensioner4 pieces 15 x 28 x 7 mm - Differentialv6 pieces 8 x 22 x 7 mm - wheel bearings2 pieces 17 x 26 x 7 mm - the inside front wheel bearingsTotal value of stock: 116,25 EUR
Special single component epoxy adhesive for bonding clutch shoes; suitable for extreme operating temperatures (up to 200°C!) Important note for processing: For the final cure of the bond Clutch-Safe must be tempered at 170°C for 1 hour! (1 hour at 170°C in the oven!) The extremely high temperature load on the clutch shoes when used in off-road cars caused by increased clutch slippage, the shock of jumps and the combination with sometimes very high vehicle weights (up to 18 kg!) make bonding with Clutch-Safe highly recommended. For later removal/replacement of worn out clutch pads the clutch shoes must be heated as well.Attention:Clutch-Safe adhesive must be stored in the fridge! Content: 10g tube
These cask shaped springs are especially designed to fit the diameters of Mecatech Klick-Shocks and Mecatech Big Bore shocks.Dimensions:Inner diameter, upper: 20,5 mmInner diameter, lower: 16,5 mmOutside diameter: 29,5 mmLength: 52,5 mmWire diameter: 2,5 mm
To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.
Genuine HT spare/option part.Rear upper alloy wishbone with droop stop. Replacement for plastic wishbone FG 6074/02.Will also fit the following Carson/Smartech cars:Onroad chassis C5, Attack, Super Attack, Gas Blaster and TouaregCarson Comanche, Attack Evo, CRT + CPT when installedwith 75 mm turnbuckle y0988Comes with 2 M8 low height nuts included. Contents:2 pieces
Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces
Genuine HT spare/option part.New designed rear lower alloy wishbone with replaceable guide bushes.Suitable for all FG 1:5 models with a width up to 400mm.Does also fit Carson Attack and Super Attack (not Evo!), C5, Smartech Spider and Ranger cars; also for Reely R5 and Big Pyro when used in combination with turnbuckle 6100/04.Please note: must use hinge pins 6075 instead of 6073!Scope of delivery:1x Alloy wishbone1x Socket head cap screw: 4 x 20 mm1x Socket head cap screw: 3 x 14 mm1x Socket head cap screw: 4 x 25 mm1x Washers steel 4,3 mm1x self-locking hexagon nut M42x hex nut M8 l/h thread4x Bearings with flangeContents:1 piece
Genuine HT spare/option part. Suitable for all FG 2WD and Smartech/Carson 2WD models except Evo 04/Competition 07/EVO 07 and Formula 1. Content:2 piece
28-piece set of sealed 2RS ball bearings for Losi 5ive-T 2.0. Set includes:4 pieces 6x10x3 mm (LOSA6946)4 pieces 10 x 15 x 4 mm (LOSB5970)4 pieces 9 x 20 x 6 mm (LOSB5974)4 pieces 12 x 24 x 6 mm (LOSB5972)6 pieces 15 x 24 x 5 mm (LOSB5973)2 pieces 15 x 28 x 7 mm (LOSB5975)4 pieces 20 x 32 x 7 mm (LOSB5971) Total of Losi prices for this 28-piece sealed bearings set when bought separately: 171.79 EUR
24-piece set of sealed 2RS ball bearings for Losi 5ive-T and Mini WRC. Set includes:4 pieces 10 x 15 x 4 mm (LOSB5970)4 pieces 9 x 20 x 6 mm (LOSB5974)4 pieces 12 x 24 x 6 mm (LOSB5972)6 pieces 15 x 24 x 5 mm (LOSB5973)2 pieces 15 x 28 x 7 mm (LOSB5975)4 pieces 20 x 32 x 7 mm (LOSB5971) Total of Losi prices for this 24-piece sealed bearings set when bought separately: 156.89 EUR
€69.90*
This website uses cookies to ensure the best experience possible. More information...