20 products found for "y1380"
rc-car-online - Home
3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.
Unfortunately, the pin striping lines on the body shell have not been applied very carefully and should be reworked individually, if you place value on it. The body shell is vac-formed from 2 mm Lexan.Measures:Length: 890 mmWidth: 392 mmHeight: 220 mmRequired body mounts:Mount front: FG 7020/16 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts
Best adhesion properties on many different materials: many metalls like steel / aluminum / stainless steel, many plastics, rubber, porous / absorbent materials.Mixing ratio: 4:1Processing time: approx. 35 minutes Temperature resistance: -20°C to +80°C, short term up to +120°CFeatures:ThixotropicDrip freeExtremely impact resistantMechanical editableGap fill up to 6 mmApplications overhead and in vertical locationsGood chemical resistanceLow bloomingColor: grey
Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)
Race ported top end set for Zenoah G320 engine.The SPEED TEC EXPERT genuine Zenoah G320 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intakeTransfer port covers:Glued and ready for use Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome groundSet includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portTo achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ().
Fits 5ive-T 2.0 as well!Set includes:y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 All steel linkage steering servo/servo saver applicationy1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1308/01 + y1308/02 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and MiniGenuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 sety1309 All steel linkage for Losi 5ive-T and Mini steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece
%
Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece
The Maxi-Pin competition tire is particularly suitable for tracks with a hard packed surface, as well as for tracks with a higher percentage of carpeting. The tread is not extended into the tire?s sidewall to reduce the side bite of the Maxi-Pin tire; the car remains controllable on such challenging tracks, which makes this tire a must-have for your "tire box"! Since the Maxi-Pin tire has many fine pins for a high number of biting edges and a low tread depth for reduced flex work, depending on the track's surface increased tire wear may be expected.Unit pricesOne pairMaxi-Pin tires39.90 EUR79.80 EUROne pairTire inserts9.90 EUR19.80 EUROne pair32482 Buggy rim14.90 EUR29.80 EUR64.70 / 129.40 EURDimensions:Diameter: 155 mmWidth: 67 mmInner diameter: 106 mm
Genuine Speed-Tec spare/option part. Contents:1 piece
Fits Area 5ive-T clutch bell holder AREA-5T-009. Both sides sealed (2RS) for increased dirt resistance. Does not fit stock parts!Content:Two pieces
Fits Area DBXL clutch bell holder AREA-XL 003 and rear uprights AREA-XL 021. Both sides sealed (2RS) for increased dirt resistance. Does not fit stock parts!Content:Two pieces
Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal
Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm
y1388 Version:
y1388/05 - 2,9 x 110 mm White, 1 pair
Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/07 - 3,2 x 110 mm Pinky1388/08 - Complete set, unit prices: 132,93 EUR / Offer price: 89,99 EUR
y1308 Version:
y1308/02 Mount B+ 7.5EUR
Genuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 set
Variants from €44.90*
Original Carson/Smartech item Unfortunately the body has a crack in the rear area and is therefore sold as used. See photos, the damage can be seen in the last photo.The body mounting holes are drilled for Smartech/Carson models.Unfortunately, the pin striping lines on the body shell have not been applied very carefully and should be reworked individually, if you place value on it. The body shell is vac-formed from 2 mm Lexan.Measures:Length: 890 mmWidth: 392 mmHeight: 220 mmRequired body mounts:Mount front: FG 7020/16 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 8013 Body mountsSide body mount rear: FG 3014 Body mounts
Original Carson/Smartech item Unfortunately, the body has some minor damage to the paintwork and is therefore being sold as used. See photos, where the damage can be seen. The left window pane has already been cut out for better air circulation. The body mounting holes are drilled for Smartech/Carson models.Unfortunately, the pin striping lines on the body shell have not been applied very carefully and should be reworked individually, if you place value on it. The body shell is vac-formed from 2 mm Lexan.Measures:Length: 890 mmWidth: 392 mmHeight: 220 mmRequired body mounts:Mount front: FG 7020/16 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 8013 Body mountsSide body mount rear: FG 3014 Body mounts
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
Genuine SCZ spare/option part. CNC-machined 6061-T6 aluminum engine mount for the SCZ 290E, required for installation in the Losi DBXL.Contents:1 piece
Genuine SPEED TEC spare/option part.Content:1 piece