y1320 Narrow-Grip 616 type drift tires, mounted and with 24 mm hex for Losi, HPI, MCD

The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs.  - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.

Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available with either 18 mm square drive to fit FG & co. To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the square or hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims for FG, Smartech and Co.:y1400/01 - Tarmac Bustery1401/01 - Big Digger y1402/01 - Cross Bond y1403/01 - Over Lander y1404/01 - Giant Grip y1416/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (18 mm square for FG Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.Contents:2 pieces / 1 pair

Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.

GIANT GRIP 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced orange beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe MadMax Giant Grip tires use 60 mm wide rims ( y1415/01 or y0761/01).The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

Big Bully GR1 - the new 4WD metal model from UFRC incl. RTR equipment! TT56112/520Top Tuning Monster Brushless Motor 520kV HW3010420 Hobbywing Ezrun MAX5 HV G2250 Amp ESC Spektrum DX6C 6-Channel DSMR Transmitter with SR315 Receiver 2 pieces y1570 CYS S0650 large scale servo, 55 kg/0,11 sec for Steering 2 pieces y2009 Top Tuning Digital pro Servo 25 kg for Differential lock Required for completion: 2 pieces of 6S batteries with EC8 connectors (total max. size for both batteries combined: length 193 mm × width 125 mm × height 100 mm) Charger for LiPo batteries Besides its excellent workmanship, there are many special details that clearly distinguish it from other vehicles on the market: Its external dimensions are not much bigger than those of a 1/6 car, yet its wheelbase is on par with many 1/5 cars and it has no overhangs at all; its tires fit a monster truck (230 mm diameter!). This results in amazing handiness for a large scale car combined with outstanding off-road capability. The GR1 comes out of the box almost as an all-metal vehicle. Tuning parts to reinforce the model are no longer necessary. Center and rear differential come standard with mechanical locks which can be activated independently by the radio. Of course, a radio system with the appropriate number of channels is required to use this feature. The dimensioning of all parts is designed for great reliability, e.g. the ball joints in the lower trailing arms are standardized industrial swivel bearings with an inner diameter of 6 mm, and the driveline can handle 12S hands down. But according to our experience, 12S operation is simply unnecessary. Nevertheless, we offer 12S equipment in the options menu. Oversized drive shafts also on the front axle are machined and hardened steel with fixed joints at both ends and sliding piece for length compensation. The tires feature a vulcanized fabric reinforcement made of Kevlar; ballooning is actually a thing of the past for them. Thanks to Kevlar, the fabric belt can be relatively thin, so the tires are soft and flexible despite the fabric. Aluminum servo arms for all 4 servos (steering and differential locks) are standard. The levers of the two steering servos are adjustable. Each steering servo has its own adjustable servo saver. A stainless steel adjustment tool is included. The Ackerman rod features four ball bearings. Shock absorbers with 8 mm piston rods and hard anodized shock bodies. All drive gears milled from steel and hardened. Two voltmeters can be optionally installed in the receiver box to monitor the traction batteries. The cage can be removed with only 4 clips, but even that is not a requirement for battery replacement. Inclusive original FG Monster Buggy body shell with rear wing. Big Bully GR1 (1/5 4WD solid rear axle)Main features of the 4WD Big Bully GR1: The strength of the components supports 12S power The wheelbase of 1/5 scale cars: 565mm The length of 1/6 scale cars: total length 790mm (when equipped with wheels with a diameter of 230mm) The whole car uses mostly metal parts, so there is no need to spend a lot of money on option parts later. The weight of the GR1 ready to run with 2x 4S/10.000 mAh batteries and 700KV motor is about 22 kg.But if you think now that this is a ponderous steamroller, you better think again. A "Tank on speed" is a better description. Despite the weight, wheelies can be called up at any time thanks to the appropriate gear reduction, even if the controller is only set to level two of four in acceleration (punch).At the same time, the possible twisting of the chassis is almost like that of a crawler. With the diff locks activated, the GR1 is almost unstoppable. Technical details: Drive train: full-time 4WD with 3 differentials (remote rear and center differential lock as standard equipment) Front suspension type: double a-arm IFS Rear suspension type: solid rear axle with 4-link suspension Scale: 1/5 Wheelbase: 565mm Front track width: 420mm Rear track width: 420mm Caster angle of kingpin: 20 degrees Front camber (adjustable): 3 degrees Toe-in (adjustable): 3 degrees Rear toe-in (not adjustable): 0 degrees Rear camber (not adjustable): 0 degrees Approach angle: about 90 degrees Departure angle: about 90 degrees Break-over angle: about 45 degrees Minimum turning radius: about 1.5 meters The maximum steering angle: about 30 degrees Maximum gradient: about 50 degrees Slide slope: about 40 degrees Maximum articulation: about 80 degrees (need to remove the front and rear anti-roll bars and loosen the angle limit screws of the front shock mounting beam) Lower trailing arm length (center/center of spherical bearings): 257 mm Chassis ground clearance (wheel diameter 230 mm): 115 mm Ground clearance under rear differential (wheel diameter 230 mm): 75 mm The maximum external dimensions of the vehicle body (length × width × height): 790 mm × 525 mm × 380 mm (with wheels of 230 mm diameter and 100 mm width) Gear ratio range: 9:1 to14.9:1 (The gear ratio can be changed by different gear set in the center gear box) Factory standard gear ratio: 14.9:1 Gear modulus: M1.5 Number of locking differentials: 2, servos for activation not included Locking differential positions: center and rear Wheel size: diameter 230 mm; width 100 mm. The tires feature Kevlar fiber belt to prevent ballooning and can handle 12S power Wheel drive size: 24 mm hex Front shocks mounting length (two-stage springs): 170 mm Front shock travel: 53 mm Rear shock mounting length (two-stage springs): 212mm Rear shock travel: 80 mm Calculated top speed: 8S power: 80 km/h (based on a 750KV motor) 12S power 110 km/h (based on a 680KV motor) (The maximum speed is calculated based on the electronic components and the actual numbers may vary) Weight of empty frame (excluding wheels and electronic components): 13.5 kg Total weight: approx. 22 kg Maximum payload of the frame: about 10 kg (do not press heavy objects or let people sit on the frame for driving operations, which may cause damage to parts) Lubricants parameters Front shock oil (silicone oil): 100cst Rear shock oil (silicone oil): 100cst Front differential oil (silicone oil): 300,000 cst Center differential oil (silicone oil): 300,000 cst Rear differential oil (silicone oil): 300,000 cst Front gearbox (grease): Swedish molybdenum disulfide high temperature grease (blue) Center gear box (grease): Swedish molybdenum disulfide high temperature grease (blue) Rear axle gearbox (grease): Swedish molybdenum disulfide high temperature grease (blue) (The above lubricants parameters are for reference only, and can be replaced according to your driving habits and environment) Frame materials and parts specifications, etc. Chassis Material: AL6061-T6 (aluminum) Processing technology: CNC machining, no stamp-out processing Surface treatment: hard anodizing and hardening Specifications: thickness 5 mm Front skid plate plate (standard configuration) Material: AL6061-T6 (aluminum) Processing technology: CNC machining non-casting Surface treatment: hard anodizing and hardening Specifications: thickness 5 mm Lower trailing arms Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specifications: The thickness of the part is 30 mm Front gear box housing Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specification: wall thickness 4 mm Center gear box housing Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specifications: wall thickness 2.5 mm Rear axle Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: anodizing Specifications: wall thickness 4 mm Front spindles Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: hard anodizing and hardening C-Hubs Material: AL6061-T6 (aluminum) Processing technology: CNC machining Surface treatment: hard anodizing and hardening Differential ring and pinion (front and rear) Material: high-strength billet gear steel, non-powder metallurgy Processing technology: CNC gear hobbing machine Heat treatment process: carburizing and hardening Modulus: M1.5 Center gear box spur gears Material: high-strength billet gear steel, non-powder metallurgy Processing technology: CNC gear hobbing machine Heat treatment process: carburizing and hardening Modulus: M1.5 Differential spider gears Material: steel-based powder metallurgy Processing technology: hot isostatic pressing sintering Heat treatment process: vacuum Differential locking clutch Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Front suspension drive shaft (CVD structure at the wheel end, universal joint structure at the gear box end) Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specifications: CVD end shaft diameter 12 mm; gearbox end universal joint maximum outer diameter 32mm Center drive shaft Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specification: shaft diameter 12 mm Rear universal drive shaft Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specifications: The outer diameter of the spline telescopic shaft is 12 mm; the maximum diameter of the universal joint is 32 mm. Rear axle shafts Material: high-strength billet carbon steel Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Specifications: shaft diameter 12 mm, non-pin positive locking structure, shaft reaches into the differential planetary gear. Front bumper Material: high strength nylon Roll cage Material: high strength nylon Specification: diameter 10mm Car body shell Material: Polycarbonate Specifications: thickness 1.5 mm Original FG Monster Buggy body shell # 54150/01 with rear wing # 58150/02 Receiver box: nylon Front and rear shock absorption main parts Upper shock cap Material: AL6061-T6 (aluminum) Processing technology: CNC Surface treatment: anodizing Shock body Material: AL6061-T6 (aluminum) Processing technology: CNC Surface treatment: hard anodizing and hardening Specification: barrel diameter 28mm Shock spring Material: piano wire Surface treatment: black nickel plating Specification: front 2.8mm/rear 2.5mm Shock piston rod Material: high-strength carbon steel Processing technology: high precision grinding Heat treatment: carburizing and hardening Specification: diameter 8mm Spring perches Material: nylon Piston Material: nylon Processing technology: CNC machined, no injection molding Sealing ring Material: silicone Front shock mounting beam: AL6061-T6 (aluminum) Rear shock tower: AL6061-T6 (aluminum) Servo fixing frame: AL6061-T6 (aluminum) Steering rods Material: high-strength carbon steel Specification: 6mm Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Steering linkage rods Material: high-strength carbon steel Specification: 6mm Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Rear axle stabilizer bar Material: high-strength carbon steel Specification: 6 mm Processing technology: CNC Heat treatment process: carburizing and hardening Surface treatment: electroplating Ball heads Material: SUS304 stainless steel Specification: ball diameter 11 mm Front lower A-arm: high-strength nylon Center gear box mounts: AL6061-T6 (aluminum) Lower trailing arm brackets: AL6061-T6 (aluminum) Adjustable steering servo arm (comes as standard!): AL6061-T6 (aluminum) (adjustment angle 20 degrees) Wheels Specifications Diameter: 230 mm Width: 100 mm Hexagonal drive: 24 mm Material Rim: high-strength nylon Tire skin: natural rubber (Kevlar fiber belted) Liner: high elastic sponge Hex drive: The hex insert is powder steel metallurgy, and the outer reinforcement ring is SUS304 stainless steel All vehicle screws: 10.9 grade carbon steel General components: Wheels: Most 1/5 scale wheels with 24 mm hex drive and a diameter ranging from 190-230 mm and a width of 70-100 mm can be used. When the diameter is greater than 190 mm and the width is greater than 80 mm, the steering angle needs to be limited, and the steering angle has to be adjusted on the transmitter to about 75%. It is recommended to use wheels with a diameter of 230 mm and a width of 100 mm to maximize the performance and handling of the car. Differential spider gear assembly: HPI BAJA 5B compatible Nylon ball joints: 5ive-T size (ball diameter 11 mm) Electronic components configuration ESC Specification: 8S-12S Quantity: 1 Motor Specifications: market standard motor for 1/5 vehicles, such as 5692/56112/58113 When using 8S power, the motor KV value should be lower than 800. When using 12S power, the motor KV value should be lower than 600. When selecting a 12S motor, you should accurately consult whether it supports 12S power. Improper selection may cause serious damage to the motor. The diameter of the motor shaft is 8 mm, and the depth of the flat surface is 1 mm. The protruding length of the motor shaft should be greater than 20 mm and less than 40 mm. Quantity: 1 Battery 8S: 2 groups of 4S (6,000-12,000 mAh) in series 12S: 2 sets of 6S (6,000-12,000 mAh) in series When choosing a battery, it should be noted that the three-dimensional size of the two batteries together cannot be larger than the size of the battery compartment. Quantity: 2 packs Battery compartment size: length 193 mm×width 125 mm×height 100mm Steering servo: Specification (15T output shaft): 50-85 kg Use common 1/5 model servos (mounting bolt pattern 17.5 mm×75 mm). Quantity: 2 Differential lock servo Specification (25T output shaft): 15-35 kg Use common 1/8 model steering servos ( mounting bolt pattern 10.0 mm × 49.5 mm), it is recommended to use 25 kg steering gear, but it should not be stronger than 35kg, which may easily cause the displacement of the differential lock limiter and change the pulling stroke. The differential lock function fails. Quantity: 2 Remote control Type: car Channels: 5 channels or more (steering; throttle; differential lock uses two channels; car lighting (optional) channel) Quantity: one set Charger Type: Equipped with lithium battery balancing function Specifications: 4S or above Quantity: one set Battery safe storage container Common tools Tool type: Allen key wrench; Hex wrenches; circlip pliers Allen wrench Sizes (metric system): 1.5 mm; 2.0 mm; 2.5 mm; 3.0 mm; 4.0 mm; 5.0 mm Hex wrenches Sizes (metric system): 7 mm; 8 mm; 9 mm; 10 mm Circlip pliers Type: external circlip pliers (when gripping the handle of the circlip pliers, the front end should open outward) Specifications: The diameter of the tip is less than 1mm, and the use range is 4-10mm