40 products found for "tlr_352001"

rc-car-online - Home

TLR352001 TLR Cross Pins & Support blocks for 5ive-T/2.0, TLR 5ive-B and Mini WRC

Genuine TLR spare/option part.Content:12 pieces Support blocks6 pieces Cross pins

€35.99*

TLR353001 TLR shock shaft, front, TiCN coated, 5ive-T/2.0, TLR 5ive-B and Mini WRC

TLR shock shaft for Losi 5ive-T front shocks; TiCN (titanium carbon nitride) coated; approx 83.3 mm long.Direct replacement for stock shock shaft LOSB 2851.

€29.99*

TLR354001 TLR hinge pin, rear outer, TiCN coated, 5ive-T/2.0, TLR 5ive-B and Mini WRC

TLR hinge pin for Losi 5ive-T, TLR 5ive-B and Mini WRC, rear outer; TiCN (titanium carbon nitride) coated; approx 79.5 mm long.Direct replacement for stock hinge pin from the set LOSB 2080.Contents:2 pieces

€19.99*

TLR351001 TLR Front top Chassis brace alloy, 5ive-B, 5ive-T

Genuine TLR spare/option part.Spare part for TLR/Losi 5ive-B, 5ive-T and Mini WRC.Contents:1 piece

€39.99*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

LOS352001 Spur Gear, Center Diff, 62 teeth, 5ive-T/2.0 and Mini

Genuine Losi spare/option part. Gear table:Gears:Ratio:Slug:LOSB5046 18 Teeth pinion / 18 to 6211,39LOSB5804 Engine MountLOSB5044 19 Teeth pinion / 19 to 6210,79LOSB5803 Engine MountLOSB5045 20 Teeth pinion / 20 to 6210,25LOSB5805 Engine MountThe 62T spur gear is also very helpful with brushless conversions, creating more space between motor and center diff. This allows the use of smaller pinions for all those, who are not into top speed only.Contents:1 piece

€89.99*

LOS352009 Losi Wheel Nut, Captured, Black, DBXL-E 2.0

Genuine Losi spare/option part. Contents:4 pieces

€39.99*

LOS352008 Losi Pinion Gear and Hardware, 22T, 1.5M for 5ive-T 2.0

Genuine Losi spare/option part. Contents:1 piece

€29.99*

LOS352002 Losi Center Diff Spur Gear, 50T, DBXL-E

Genuine Losi spare/option part. Contents:1 piece

€49.99*

LOS352007 Losi Pinion Gear and Hardware, 21T, 1.5M for 5ive-T 2.0

Genuine Losi spare/option part. Contents:1 piece

€29.99*

LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:2 pieces

€39.99*