6104/01 FG Front axle shaft, 57 mm
€11.90
Available
Product information "6104/01 FG Front axle shaft, 57 mm"
Diameter 8 mm.
Contents:
- 1 piece
Login
Accessories / Spare parts
Genuine FG spare/option part. Fits FG + Carson 6 mm a-arm hinge pins and 8 mm front wheel shafts.Part is delivered in silver or black color from vendor!Content:15 pieces
Alternatives
Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece
Genuine HT spare/option part. With flat section for the wheel drive set screws.Dimensions:Diameter: 8 mmTotal length: 56 mmLength up to the groove: 54 mmThread length: 10 mmThread size: M6Contents:2 pieces
Customers also bought
Fits all FG cars and the Mecatech FW01. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Diameter: 8 mmTotal length 76.6 mm
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces
Decal set for FG Street truck.Dimensions:470 x 250 mm
Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces
Customers also viewed
Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece
Genuine FG spare/option part. Dimensions:Length: 65 mmThread length: approx. 12 mmLength from thread to clip: approx. 47 mmSpace between clips: approx. 4 mmDiameter: 8 mmContents:1 piece
Genuine Mielke spare/option part. Contents:4 pieces
Genuine FG spare/option part. Suitable for all FG models. Only useable with 9,5mm square driver.Diameter 8 mm.Contents:1 piece
Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Contents:10 pieces
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (wishbone pin), too. Fits the rear axle of all FG offroad cars (2WD and 4WD) and all Carson / Smartech cars.Content:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm