y0735 Safety clip for Universal / JR / Futaba connectors
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
y0362 Servo direct power supply cable, 1 pce. selection
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section
6547 FG Receiver cable FG gold contact/Futaba - 1pce.
Receiver cable, ready-made with FG gold contact plug-in system for Futaba plug.total length 20-25cm
y0425/01 Y-harness, silicone insulated, universal/JR
Genuine HT spare/option part. The Y-harness is required for running two servos on a single receiver channel. Top quality heavy gauge 0.5 mm² cable with silicone insulation, 150 mm long, suitable for all rc-systems.Content:1 piece
F003/2 Carson Universal On/Off Switch
Genuine Carson spare/option part. Contents:1 piece
TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
Receiver switch, universal connectors, F1408 - 1pce.
Futaba / universal type connectors for both battery and receiver.
Receiver switch, BEC connectors, cs503024 - 1pce.
BEC type connectors for both battery and receiver.
6551 FG Receiver cable with switch FG/JR
Genuine FG spare/option part. Waterproof switch equipped with JR connector for receiver and FG gold contact connector for the receiver battery. Used to cut the power supply of receiver and battery. With fastening screw thread.Suitable for all radio control systems.Contents:1 piece
y0210 Receiver switches, water protected, all conectors
Genuine HT spare/option part. Water protected receiver switches, silver plated contacts. Many different connectors to choose from.UniversalFGBECHigh currentContents:1 piece
Servo direct power supply cable with electronic switch, 1 pce.
Servo direct power supply cable with electronic switch, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.The integrated electronic receiver switch is rated 5 A continuous / 15 A peak. This switch does not use mechanical contacts for the load; therefore it is less prone to failure caused by vibrations or dirt. With separate charging connector.With drilling template and mounting material included.
y1251, Adapter cable BEC/FG, 1 pce.
This adapter cable allows for the use of LRP LiPo or LiFePo receiver batteries in cars with FG gold plated connectors without altering the existing wiring.
y0533 Adapter cable for LRP Jet-Pro Charger
Genuine HT spare/option part. Adapter cable for all usual rx-battery connectors, especially for use with the LRP Jet-Pro charger.Available applications:BEC to UniBEC to FGBEC to High CurrentBEC to Uni femaleContents:1 piece
6550 FG Switch for receiver cable
Genuine FG spare/option part. A switch which one well through a hole in the radio box and put on top and bottom can be secured with nuts.Contents:1 piece
Receiver switch, Multiplex connectors old, y0920 - 1pce.
Old version Multiplex type connectors for both battery and receiver.
6547/01 FG Receiver cable FG gold contact/Multiplex - 1pce.
Receiver cable, ready-made with FG gold contact plug-in system for Multiplex plug.total length 20-25cm
Adapter cable, high current / universal, y0922 - 1pce.
High current connector for the battery and Futaba / universal connector for the receiver.