y1036 HT rose joints with conical spacers
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
y6107 Wheel squares 18 mm HART-COAT, 9,5 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
y6107/07 Wheel squares 18 mm HART-COAT, 12 mm wide
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
y0932 HT Alloy front uprights for FG / Smartech
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
6496 FG Alloy front bulkhead 2WD A and B
Genuine FG spare/option part.CNC-manufactured front axle mounts A and B in alloy with rebound stop. The borings for the wishbone pins are equipped with guide bushes. Suitable for Marder, Marder Race, Beetle On-/Off-Road and Monster models.Contents:1 set
y0264 C-clips with handle 4 - 6 mm
Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces
Elcon 14404, front shock tower for FG Monster Truck 2WD
CNC-milled aluminum version, suitable for the old version of the FG 2WD monster and stadium models. These vehicles were distinguished by coming from the factory with four shocks each front and rear. The shock tower comes complete with mounting hardware and four quick-release mounts for the upper shock ends.
y6106/07 Wheel square 11,5mm, steel
Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm
y0626 Front axle shaft for 1/5 + 1/6 2WD cars
Genuine HT spare/option part. With flat section for the wheel drive set screws.Dimensions:Diameter: 8 mmTotal length: 56 mmLength up to the groove: 54 mmThread length: 10 mmThread size: M6Contents:2 pieces
y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars
Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces
y18005 HT-shock absorber quick mounts for Monster-Truck 2WD
Genuine HT spare/option part. Shock absorber quick mounts, for shock mounts and shock tower above. Sold in pairs. Contents:2 pieces
y0937 HT Replacement body for y0932
Genuine HT spare/option part.Spare part for y0932.Contents:1 piece
6103/06 FG Alloy upright front 1:6 2WD
Genuine FG spare/option part. Suitable for all FG 2WD 1:6 Off-Road and monster models.Bearing seats: 22 x 7 mm.Contents:1 set
y18003 HT-shock mounts for 2WD Monster-Truck, front lower
Shock mounts for the lower a-arms. Sold in pairs.
y0906 HT Monster / Stadium alloy front suspension kit 2WD - 1pce.
Alloy front axle kit for FG Monster and Stadium 2WD models. Complete kit with all necessary parts. A-arms and bulkheads feature replaceable bushings, shock stay, shock quick mounts, balljoints, and droop stop.Fits FG Monster and Stadium 2WD models.All components are available separately.Quantity Order N° Kind 2 pieces 18000 A-arm front upper 2 pieces 18001/l+r A-arm front lower 2 pieces 18006 Front bulkhead 1 piece 18004 Shock tower2 pieces 18003Shock mounts4 piece 18005 Absorber quick mounts1 piece 18007 Suspension travel limiter2 pieces y1036 Rose jointsThe price of those parts bought separately would be 451,80 EURIf you want to install front cable brakes, we recommend the brake cable bracket below.
50607140 Lightscale Wheel square 14 mm
Genuine Lightscale spare/option part.Square Hub 14 mm with additional steel pins to secure wheels from damage due to turning on the hub.The Lightscale Diamond square hub is reduced to the maximum possible weight saving but serves even better lining and stiffness for the wheel and the brake disc. Furthermore the hub is slightly conical to its outside which makes mounting the tires easier especially in hectically racing situations.The Diamond is available in 11,5, 12 mm and 14,5mm width and fit all common known brands such as FG, RS-5, H.A.R.M. or Contrast and many more as well as all kinds of cars like on road, off road or Formula 1.Contents:2 pieces
y18000 HT-alloy a-arm for 2WD Monster-Truck, front upper
Genuine HT spare/option part. Upper a-arm with replaceable bushings. One piece per pack.Contents:1 piece
y18004 HT-alloy shock tower for 2WD Monster-Truck
Shock tower, replaces FG # 6099/1.
6496/02 FG Alloy front bulkhead 2WD B - 1pce.
CNC-manufactured front axle mount B in alloy. Suitable for 2WD Marder, Marder Race, Beetle On-/Off-Road and Monster models.
6497 FG alloy front axle for 2WD Monster-Truck models for double shocks setup - set
Genuine FG spare/option part.Solid alloy front axle for all FG 2WD Monster-Stadium models for twin shock absorbers.Without Shocks and uprights.Contents:1 set
6496/03 FG Droop stop - 2pcs.
Item N° 6496/03 Droop stop - 2pcs.Suitable for 6496/01.
50586 Lauterbacher front bulkhead for FG 2WD Monster and Buggy
Genuine Lauterbacher spare/option part. Fits all FG buggies except models from the Leopard series.Can be used as bulkhead A or B.Contents:1 piece