LOSB5800/01 Losi Body clips big, 85 mm

Chassis mud flaps for the Losi 5ive-T, made of 1.0 mm extremely durable plastic material. The mud flaps are precisely contoured to follow the 5ive-Ts roll cage and body shell. Die-cut and ready for installation featuring 15 eyelets in 3 different sizes and 4 each form and hole punchings to fit the roll cage brackets. The set also includes complete hardware for installation and an illustrated manual! Dimensions of mud flaps (laying flat): 930 x 135 mm Set includes: 2 x protective cover (right and left) 6 x cable clip 14 x fixing screws 12 x washers 1 x manual

Genuine HT spare/option part. For all epoxy models, plastic and polycarbonate/lexan body repairs!Direction of use:Use a brush or other applicator. Apply enough Flexa Fix to the damaged area. Be careful not to apply too much in one go as it can be difficult to manipulate. If necessary apply two or three coats to build up the joint area. Use epoxy blanket of pieces of polycarbonate (Lexan) to re-enforce if necessary.You can also use the Flexa Fix to re-enforce the body corners (let the pure product leak into the corners) or to make flexible battery packs.Contents:1 piece / 100 ml

Fits Losi 5ive-T, 5ive Mini and many more. Wire thickness: 1,4 mm.Length: 25 mm.Content:10 pieces

Genuine Losi spare/option part.Dimensions:Decal A: width 486 mm, Hight 360 mmDecal B: width 405 mm, Hight 319 mmDecal C: width 398 mm, Hight 265 mmDecal D: width 350 mm, Hight 255 mmDecal E: width 315 mm, Hight 180 mmContents:1 set

Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini. Content:2 x body clip approx. 1.4 mm wire diameter and 85 mm toal length6 x body clip approx. 1.4 mm wire diameter and 25 mm toal length12 x body clip approx. 2.0 mm wire diameter and 43 mm toal length

Fits Losi 5ive-T, 5ive Mini and many more. Wire thickness: 2 mm.Length: 35 mm.Content:10 pieces

Genuine Losi spare/option part.Fits Losi 5ive-T and 5ive Mini.Content:56 pieces

Genuine rc-car-online spare/option part. A "must have" for every run in the dark. A total of 11 different lighting effects are programmeded into this LED module. The LED strip has the same size like that of the Losi 5ive-T 2.0 and the Losi DBXL-E and can therefore replace for the OEM version in its bracket.The LED module is typically powered by the receiver battery (maximum 7.4V). Depending on the version selected, the effects are changed via the radio (requires a free channel on transmitter and receiver) or via an onboard switch.The LED strip has on the back of an adhesive strip with which it can be glued on loose on the body. In the shop's options menu you can add an optional mounting bracket for the Losi 5ive-T. Modes:Continuous whiteContinuous white 30% intensityOffKnightRider redKnightRider whiteKnightRider blueKnightRider greenPolice 1Police 2SafetyCarRainbow chaser lightStrobo-Light whiteDimensions LED:Length: 160 mmHeight: 10 mmDimension mount:Width: 160 mmHeight orifice: 8 mmHeight behind orifice: 10 mmContents:1 set

You will need polycarbonate paint (sold separately) for the paint job when you select the clear version: Tamiya Sprühfarbe - 1St. Painting tips:

Item N° LOSB 8104/01Body right Fender and Plate black 5T, 2 pcs. Ready for installation with factory applied decals!

Genuine Smartech spare/option part.Includes the complete set 26 body mounting washers, 22 support plates and corresponding screws for an original Losi 5ive-T or Losi 5ive-Mini body.Your choice of screws with either Allen head or hexalobular drive (a.k.a. Torx) heads!Content:26 pieces of mounting washers22 pieces of support plates14 pieces of countersunk screws (DIN7991) Allen head M4 x 20, 10.9 grade Alternatively TX10 Torx head, 10.9 grade12 pieces countersunk screws (DIN7991) Allen head M4 x 16, 10.9 gradeAlternatively TX10 Torx head, 10.9 grade

Genuine Area spare/option part.The set includes 26 pieces each of aluminum mount washers and support dishes for a complete equipping of the genuine Losi 5ive-T or Mini body shell (replaces LOSB2582). Your choice of blue or orange anodized!Contents:26 pieces

Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.