Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

LOS352010 Losi Pinion Gear, 19T, 1.5M & Hardware DBXL 2.0

Product information "LOS352010 Losi Pinion Gear, 19T, 1.5M & Hardware DBXL 2.0"

Genuine Losi spare/option part.

Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

y0726/01 Gas-nitrited tuning clutch bell for Losi DBXL+MTXL
Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece

€49.90*

Average rating of 0 out of 5 stars

LOS352011 Losi Pinion Gear, 21T, 1.5M DBXL 2.0

€19.99*

Average rating of 0 out of 5 stars

y0781/01 Dry-Fluid "Gear Lube" for gears, 10 ml
Dry lubricant instead of oil DryFluid Extreme Gear Lube is specifically designed for highly loaded gears in models. It is characterized by extreme pressure resistance and excellent adhesion. Through the use of solid lubricant components, it shows only a slight tendency for dust and dirt retention. Main applications of the newly developed Gear Lube Gear are of model helicopters, rc-cars and trucks, model trains and servos. Also ideally suited for shafts and gimbals of any kind.DryFluid lubricant is more of a solid lubricant than a classic fluid one. DryFluid is not a wax, not oiling, non-greasy and free of silicones. The use of dry particles, polymer lubricants and high-end lubricating fluids results in a previously unknown lubricity without binding dust and dirt. Especially the long-term effects of DryFluid Extreme will delight any modeler. Product characteristics at a glance: Exciting lubricating propertiesReduces power losses caused by friction Reduces operating noise Reduces wear Extremely pressure resistant Long-term stability Highest adhesion High material compatibility with metals, plastics and rubber materials Low tendency for dust and dirt binding Application Notes: A thin layer of the Gear Lube is enough for an extreme lubricating effect. If possible, apply to an upright standing gear and rotate it during the application. For hard to reach places and selective applications use the included canula. For fine and uniform distribution use a fine hair brush immediately after the application of Gear Lube. Transmissions that have not been treated with Gear Lube before should be thoroughly cleaned first. Shake well before using and apply sparingly!High End dry lubricant for highly loaded gears in models. Especially for transmissions of model helicopters, rc-cars, trucks, model trains and servos. Can also be used for shafts and gimbals of any kind Through the use of dry particles, lubricating polymers and high-end lubricating fluids an unprecedented lubricating effect is achieved. Extremely pressure-resistant and with excellent adhesion. Very low tendency for dust and dirt retention. Multistage dry lubricant system with long-term effects.

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

Average rating of 0 out of 5 stars

y0781 Dry-Fluid Extreme especially for RC-Cars, 20 ml
Dry lubricant instead of oilWe did not think that today its still possible to make a real improvement in lubricants!DryFluid Extreme is especially designed for remote control model cars, with the aim to maintain the functionality and durability of these little racers as long as possible or to even extend significantly.The effect of the new lubricants for shafts, bearings, guides and ball joints starts where other lubricants reach their limits. Low friction, high lubricity and minimal attractivity to dust or dirt were the main developmental targets. Recent findings in aerospace and automotive technology as well as the experience of RC car drivers are the mentors of innovation of this new lubricant.What is DryFluid Extreme RC-Cars?DryFluid lubricant is more of a solid lubricant than a classic fluid one. DryFluid is not a wax, not oiling, non-greasy and free of silicones. The use of dry particles, polymer lubricants and high-end lubricating fluids results in a previously unknown lubricity without binding dust and dirt. Ease of application and long-term effects of DryFluid Extreme will delight any modeler.DryFluid Extreme product featuresReduces the power losses of shafts, bearings and ball joint systems and guarantees a long life of the treated componentsLowest friction for smooth operation and wear reductionMultistage lubricant system with immediate and long-term lubrication effectsDoes not bind any dust or dirtExtremely good penetrating abilityHighest compatibility with all common materials like metals, plastics and rubberExcellent adhesion and corrosion protection propertiesThe use of DryFluid Extreme RC-CarsThe main effect of DryFluid Extreme is the reduction of friction and wear on shafts, bearings, guides and ball joint systems. The dry components do not bind any dust or dirt and ensure best possible long term lubrication effects.For best results the parts to be treated should be thoroughly cleaned and the fluid applied sparingly. Repeated use increases the long-term effect.Before use, shake bottle vigorously for a short time!Nanotec lubricant for joints, shafts, bearings and gears of rc-cars. Excellent long term lubrication effects. Use included put-on canula for fine dosing. Let dry for several minutes after application and close bottle tightly. Shake well before use Attention:Keep out of reach of children. Do not swallow. Avoid contact with eyes. Keep away from ignition sources. Keep bottle closed tightly.

Content: 20 Milliliter (€845.00* / 1000 Milliliter)

€16.90*

Similar products

Average rating of 0 out of 5 stars

LOS252017 Axle Boot Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:10 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252009 Differential Rebuild Kit Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€8.99*

Average rating of 0 out of 5 stars

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

Average rating of 0 out of 5 stars

LOS252006 Front/Rear Differential Outdrive Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:2 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252135 Losi Center Driveshaft, rear: DBXL 2.0
Genuine Losi spare/option part. Contents:1 piece

€39.99*

Average rating of 0 out of 5 stars

LOS252016 20T Pinion Gear Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 piece

€19.99*

Average rating of 0 out of 5 stars

LOS252134 Losi Center Driveshaft, Front: DBXL 2.0
Genuine Losi spare/option part. Contents:1 piece

€39.99*

Average rating of 0 out of 5 stars

LOS252008 FR/R 43T Ring and 13T Pinion Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€69.99*

Average rating of 0 out of 5 stars

LOS251024 Brake Pads/Springs/Cam/Discs Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€49.99*

Average rating of 0 out of 5 stars

LOS252002 Center Dog Bone, short Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. 

€39.99*

Average rating of 0 out of 5 stars

LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:2 pieces

€39.99*

Average rating of 0 out of 5 stars

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*

Customers also viewed

Average rating of 0 out of 5 stars

AT-DBXL013 ATOP Clutch bell carrier for Losi Desert XL+MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set

€34.90*

Average rating of 0 out of 5 stars

LOS352008 Losi Pinion Gear and Hardware, 22T, 1.5M for 5ive-T 2.0
Genuine Losi spare/option part. Contents:1 piece

€29.99*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Theme Development