LOS252112 Losi 17mm Flanged Wheel Nut, Black for Super Baja Rey / 2.0 / Super Rock Rey

Genuine Losi spare/option part. Contents:4 pieces

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Genuine Losi spare/option part. Contents:4 pieces

Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm

2 pairs CROSS BOND 170 x 60 mm tires with black MadMax Extreme 20 bolt-beadlock rims with 24 mm hex drive and reinforced orange beadlock rings were designed for use on loose surfaces. The extremely rigid and differently structured lugs of the CROSS BOND ensure optimum power transmission and also allow for excellent grip on loose surfaces, such as sand and soil. The lugs are raised at the treads outside, and therefore provide maximum grip, particularly when cornering where the tire is canted to the outside. Due to the extreme load created by the MadMax CROSS BOND tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmReinforced 24 mm hex driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.