Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

LOS252058/01 Losi brushless motor mounting plate, black, DBXL-E / DBXL-E 2.0

Product information "LOS252058/01 Losi brushless motor mounting plate, black, DBXL-E / DBXL-E 2.0"

Genuine Losi spare/option part.

Aluminum brushless motor mounting plate, black, incl mounting screws for the motor.

Size:


  • Outer dimensions max. 40 x 46 x 10 mm


Contents:
  • 1 set

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0
Genuine Losi spare/option part. Contents:10 pieces

€29.99*

Average rating of 0 out of 5 stars

LOS252067 Losi Diff Rebuild Kit, Al Diff Housing, DBXL-E
Genuine Losi spare/option part. Contents:1 set

€29.99*

Average rating of 0 out of 5 stars

LOS254006/01 Suspension Arm Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Content:1 piece

€16.90*

Average rating of 0 out of 5 stars

LOS254010 Losi Hinge Pin, Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€19.99*

Average rating of 0 out of 5 stars

LOS352009 Losi Wheel Nut, Captured, Black, DBXL-E 2.0
Genuine Losi spare/option part. Contents:4 pieces

€39.99*

Average rating of 0 out of 5 stars

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL
Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

Average rating of 0 out of 5 stars

LOS254006 Losi Suspension Arm Set Losi DBXL/DBXL-E/DBXL 2.0 1/5 4WD
Genuine Losi spare/option part. Content:4 pieces

€59.99*

Average rating of 0 out of 5 stars

LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€39.99*

Average rating of 0 out of 5 stars

LOS254009 Losi Hinge Pin Brace Inserts, Set Losi DBXL+MTXL 1/5 4WD
Genuine Losi spare/option part. Contents:1 set

€9.99*

Average rating of 0 out of 5 stars

LOS252126 Drive Pin Rebuild Set DBXL-E 2.0

€9.99*

Average rating of 0 out of 5 stars

LOS252061 Losi Center Diff Spur Gear, 48T, DBXL-E
Genuine Losi spare/option part. Contents:1 piece

€49.99*

Average rating of 0 out of 5 stars

LOS252065 Losi Pinion Gear, 14T, 1.5M, 8 mm Shaft
Genuine Losi spare/option part. Contents:1 piece

€19.99*

Customers also viewed

%

Average rating of 0 out of 5 stars

HW38020369 Hobbywing Ezrun MAX4 HV Combo 70125 560kV
Product information "Hobbywing Ezrun MAX4 HV Combo 70125 560kV"The Ezrun MAX4 ESC works best with the included 70125 SD 560kV motor for extra large 1/4 and 1/5 scale models. This fully sensor-controlled combo can be used in many ways in such models, whether it's a heavy-duty off-roader or a truck.So if you like large models and You want the most fun out of it, the MAX4 combo is high-quality equipment that literally bursts with exploding power. And even with its enormous size, care was taken to use high-quality and, above all, durable materials in the construction. After all, both the ESC and the motor should ensure that driving fun lasts as long as possible. Even the electronic switch is well protected against damage. In addition, the Ezrun MAX4 has a built-in super high-current BEC, which can provide a max. output power of up to 25A. The output voltage can be switched between 6V, 7.4V and 8.4V. The high-current BEC was developed in such a way that it can supply the current high-current servos with sufficient power if required, and thus be able to precisely control the appropriate large models.Features:Full sensored comboSuper powerful switch mode BEC with a constant current of 10A, instant 25A and the ability to switch between 6V, 7.4V and 8.4VFireproof circuitry to protect the battery connector, as well as many built-in protectionsVersatile programmableReal time data recordingCNC-milled aluminum housing, 0.2mm silicon steel sheets and other high-quality building materialsFour sintered NdFeB magnets for super torque, stable performance and explosive powerInnovative new sensor interfaceWaterproof and dustproof thanks to the rubber cover of the bearingsIndependent, high-precision encoder in the motor to communicate the rotor position without any interferenceMore power and less heat development with the same loadTechnical Specifications:ESCCurrent (cont./peak)300A / 2000AMotor Type:Sensor/Sensorless Brushless MotorsMotor Limit:12S LiPo: kV <= 600 (70125)Cells:6-12SBEC:6V / 7.4V / 8.4V @ 10A (adjustable)Fan:Yes (powered by BEC)Programming Input:Fan/ PRG-InputProgramming:LED Programm Card, LCD Programm Box, OTA Bluetooth Programm ModuleDimensions:125x85x61.7mmWeight:775.4gApplication:1/4 and 1/5 Heavy Duty-Off-Road, TrucksMotorSensor Type:SensoredPoles:4kV Rating:560kVCells:8-12SNo-Load Current:3.6AOuter Diameter:70mmLength:125mmShaft Diameter:8mmShaft Length:30mmWeight:1995gApplication:1/5 Heavy Duty Off-Road, TruckDelivery:1x EzRun MAX4 ESC1x EzRun 70125SD Motor with 560kV1x Manual

€524.15* €576.00* (9% saved)
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Plugin Development