LOS252014 Clutch Bell Losi DBXL+MTXL 1/5 4WD

€39.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los252014

EAN: 605482118030

Product information "LOS252014 Clutch Bell Losi DBXL+MTXL 1/5 4WD"

Genuine Losi spare/option part.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Alternatives

y0726/01 Gas-nitrited tuning clutch bell for Losi DBXL+MTXL

Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece

€49.90*

Similar products

LOS252017 Axle Boot Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS252009 Differential Rebuild Kit Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€8.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*

LOS252006 Front/Rear Differential Outdrive Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:2 pieces

€29.99*

LOS252135 Losi Center Driveshaft, rear: DBXL 2.0

Genuine Losi spare/option part. Contents:1 piece

€39.99*

LOS252016 20T Pinion Gear Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 piece

€19.99*

LOS252134 Losi Center Driveshaft, Front: DBXL 2.0

Genuine Losi spare/option part. Contents:1 piece

€39.99*

Details

LOS252008 FR/R 43T Ring and 13T Pinion Set Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€69.99*

LOS251024 Brake Pads/Springs/Cam/Discs Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€49.99*

LOS252002 Center Dog Bone, short Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part.

€39.99*

LOS252001 Driveshaft & Axle Dogbone Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:2 pieces

€39.99*

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*