LOS252007 Center Differential Outdrive Set Losi DBXL+MTXL 1/5 4WD

Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum C-hubs from ATOP to fit all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Plastic bushings for the hinge pins ensure reduced wear. Contents:2 pieces

Genuine Losi spare/option part. Contents:10 pieces

Genuine HT spare/option part.These heavy duty differential drive cups for the center differential in a Losi 5ive-T/2.0/B or MINI WRC are made of 300M / Böhler V132 steel and are characterized not only by high hardness, but also simultaneously toughness. The service life is therefore much higher than for the stock cups. Replaces stock parts LOSB3214 and TLR252008.300M steel is used in motorsport and aviation for high strength parts. As a highly pure material, it is significantly more expensive than conventional steels, its high basic strength and toughness make the machining a time-consuming task.The 300M steel center diff drive cup has the same dimensions as the stock part.Contents:2 pieces of 300M steel HD differential drive cup, center diff application2 pieces of 4x18 drive pins

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!

The 2WD-465 Sportsline electric model is based on a short chassis (465 mm wheelbase) with double wishbones Rear and front axles built. The vehicle is factory equipped with the 2-damper front axle.E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Sportsline models are equipped with a powerful brushless engine and a Brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.In the unpainted version Version does not include a decal sheet!Features:The front axle of the GT2 was widened to 384 mm. The rear axle is 395 mm wide.Chassis short 465 with double wishbones on the rear and front axle completely assembled, ball bearings, differential gear, oil pressure shock absorber, multi-part unpainted polycarbonate body (item no. 05160L), white spoke rims, tires and tire inserts.T2M standard equipment brushless motor and ESC, 6S - 150A controller up to 3-6S  - brushless motor 6S You can order a motor/ESC combination with 8S for an additional charge.- ESC 200A, 3-8S LiPo, BEC 8A - Brushless Motor 8S The model is also available in our shop selection including complete RTR equipment! RTR features RTR = Ready to Run. The RTR version is delivered ready to drive and with the 2.4 GHz remote control installed.Decor set: selectable (included in the painted version)LiPo batteries and the appropriate charger are required for all versions of the electric models. We recommend using LiPo batteries with a maximum length of 150mm and a width of 50mm to ensure trouble-free installation. The model is supplied with an EC8 connector system.