Genuine HT spare/option part. Fully assembled Alloy differential including reinforced differential-tube and "inner-workings", such as original planetary gears, differential bevel gears, bevel differential wheel axles, sealed bearings, differential shafts with needle bearings (high-speed needle bearing).You only have to insert your full-floating axle (halfshafts). Since the FG and Carson are having different internal teeths by the planetary gears, different versions for FG and Carson/Smartech 2WD are available.Even on heavy off-road use and especially on jumps there are often problems with the original plastic differential. Noticeable is also the relatively thin differential-tube of the serial-equipping. Therefore our special offer for the complete Alloy differential including extra reinforced differential-tube.Set includet:8486 Alloy differential housing6068 Bevel differential gear axle6066/01 Differential bevel gear A, spline drive 6067 Differential bevel gear BFG ball bearings, sealed, y19610-rsReinforced differential tube for FG buggy differential, y09028498/01 Needle bearing for alloy differentialContents:1 set
Alloy case conversion kit for Carson Gas Devil 4x4 (Smartech Titan) only, can be used for all differentials.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.
Set includes 2 rotors, 4 brake pads and 4 return springs. The steel rotors will last significantly longer on the differential drive cups, wear between rotors and brake pads is reduced as well.
Item-No.: s054320/01Brake pads for Smartech tuning brake
Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set
Genuine HT spare/option part. Suitable for all FG 2WD and Smartech/Carson 2WD models except Evo 04/Competition 07/EVO 07 and Formula 1. Content:2 piece
Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece
Complete pre-assembled set front disc brakes for FG Marder, FG Off-Road Buggy and for Carson / Smartech Attack / Comanche / UNO / Monster Truck / CRT / CPT / Super Attack / Evo Attack / Spider / Big Attack , fits Conrad Big Pyro as well.For mounting in a Gas Blaster you must change you front shock mount and the front body shell holder, look at the pictures. Includes:- brake system with linkage- uprights- bearings- longer axle shafts- wider square drivesNo additional parts needed.