GPM SB237S Rear driveshaft for Losi Super Baja Rey / Rock Rey, all steel
Product number:
gpm_sb237s
EAN:
4894538317183
Product information "GPM SB237S Rear driveshaft for Losi Super Baja Rey / Rock Rey, all steel"
Genuine GPM spare/option part.
Reinforced rear drive shaft from GPM, suitable for Losi Super Baja Rey / Rock Rey for connection of center diff and rear axle, hardened all-steel version. Much stronger than the standard version with plastic center section. Replacement for LOS252072.
Contents:
Reinforced rear drive shaft from GPM, suitable for Losi Super Baja Rey / Rock Rey for connection of center diff and rear axle, hardened all-steel version. Much stronger than the standard version with plastic center section. Replacement for LOS252072.
Contents:
- 1 piece
Login
Accessories / Spare parts
Genuine GPM spare/option part. Stainless steel replacement bolts fit not only GPM driveshafts SB237S, but Losi stock driveshafts LOS252072 and LOS252110 as well. Contents:2 pieces / 1 pair
Alternatives
Genuine GPM spare/option part. Upper GPM aluminum a-arms for Losi Super Baja Rey with replaceable ball joints and plastic bushings. The higher stiffness of the aluminum parts increases steering precision and suspension response. Contents:4 pieces / 2 pairs
Customers also bought
OVER LANDER 170 x 80 mm and 170 x 60 mm tires with reinforced beadlock rings on black rims. The OVER LANDER were designed as all-terrain tires that can be used on virtually all surfaces because of its tightly attached lug tread pattern When a terrain includes sand, gravel and grass, the Overlander is the right choice! It can even be used on partially paved tracks!Of course, the OVER LANDER allround tire will not make special purpose tires like the TARMAC BUSTER,BIG DIGGER or CROSS BOND obsolete. Due to the extreme load created by the MadMax OVER LANDER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars. We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!
Genuine Losi spare/option part.The set is for two tires (one pair).Content:1 set
Genuine Losi spare/option part. Contents:2 pieces
Genuine Losi spare/option part. Contents:2 pieces
The GPM stainless steel trailing arm and steering linkage set for Losi Super Baja Rey contains a billet aluminum servo arm, the link rod from servo to servo saver, the steering rods and the upper trailing arms. Turnbuckle style rods made of stainless steel are used. This allows to change the length of these rods easily without disassembly and the suspension setup can be changed.
Genuine Losi spare/option part. Contents:1 pieces
Genuine GPM spare/option part. Motor mount with cooling fins for Losi Super Baja Rey / Rock Rey made by GPM, machined from high grade 6061-T6 aluminum. It replaces the weaker cast stock version and adds some cooling to the motor.Contents:1 piece
Similar products
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Genuine Top Tuning spare/option part. Indispensable for optimal suspension tuning!Vacuum container for removal of bubbles from shock fluid when filling shocks.A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled". Tray bore sizes: No. 1 = 32 mm diameter No. 2 = 21 mm diameter No. 3 = 17.5 mm diameter No. 4 = 15 mm diameter The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)Operation:Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort. Content: Can with integrated vacuum pump Shock tray
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting.
Please note: the wide rear wheels from MadMax or HPI do not fit!
This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
Hobbythek car bag for 1/6 cars.
Fits for all 1/6 models for example: FG Offroad-; Monster/Stadium-; Racetruck-; Carson-; Smartech-; Reely Carbon Fighter; Losi Super Rock Rey, Super Baja Rey, Axial Jeep and any more models.
Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.
No dirt in the car boot!
Dimensions:
Length: 70 cmWidth: 50 cmHeight: 40 cm
Genuine GPM spare/option part. Rear wheel bearing carriers for Losi Super Baja Rey / Rock Rey, 0° toe-in (stock) made by GPM, machined from high grade 6061-T6 aluminum provide better fit for the bearings and therefore increase their life span.We recommend installing the ball bearings with a little dab of screw cement.Contents:2 pieces
Genuine GPM spare/option part. GPM's aluminum rear shock tower for the Losi Super Baja Rey / Rock Rey is much more rigid than the standard plastic part. It offers an increased number mounting positions for the shock and therefore allows for a more precise setup. Contents:1 set
Genuine GPM spare/option part. Stainless steel replacement bolts fit not only GPM driveshafts SB237S, but Losi stock driveshafts LOS252072 and LOS252110 as well. Contents:2 pieces / 1 pair
Genuine GPM spare/option part. GPM 18T steel motor pinion for Losi Super Baja Rey / Rock Rey, also suitable for other models at your own discretion. Module 1.5 mm, bore for 8 mm shaft.We supply the pinion exclusively in a nitride hardened version. This curing has already proved extremely successful with the GPM clutch bell pinions for the Losi 5ive models and ensures significantly increased wear resistance.Contents:1 piece
Genuine GPM spare/option part. Diff housing for Losi Super Baja Rey / Rock Rey made by GPM, machined from high grade 6061-T6 aluminum. Fits front, center and rear application. Much stronger and more heat resistant than the stock plastic parts.Contents:1 piece
Genuine rc-car-online spare/option part. Komplete set of screws, nuts and washers for the Losi Super Baja Rey.The set includes a total of 321 screws, in different quantities which are all used on the Losi Super Baja Rey / Rock Rey.6 sizes of cap head screws11 sizes of CSH screws13 sizes of button head screws6 sizes of set screws3 sizes of washers4 sizes of self-locking nutsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:4 piecesM2x101 piecesM2,5x813 piecesM3x102 piecesM3x122 piecesM3x165 piecesM3x306 piecesM3x45 CSH screws in 10.9:5 piecesM2,5x86 piecesM3x66 piecesM3x1234 piecesM3x161 piecesM4x1010 piecesM4x122 piecesM4x149 piecesM4x166 piecesM4x1814 piecesM4x202 piecesM4x25Button head screws in 10.98 piecesM3x89 piecesM3x195 piecesM3x126 piecesM3x1616 piecesM3x204 piecesM3x304 piecesM3x3512 piecesM4x128 piecesM4x1618 piecesM4x2010 piecesM4x2512 piecesM4x301 piecesM4x35Grub screws:2 piecesM3x63 piecesM4x46 piecesM4x56 piecesM4x61 piecesM5x48 piecesM5x30Washers:Unterlagscheiben:5 piecesM3,25 piecesM4,34 pieces H5 Seeger HalfmoonSelf-locking nuts:4 piecesM335 piecesM4Nuts:2 piecesM45 piecesM5
Genuine GPM spare/option part. Front lower hinge pin plates from GPM for Losi Super Baja Rey / Rock Rey. Precision laser-cut from 3 mm stainless steel. Contents:2 pieces
Customers also viewed
%
The DBXL Platform has been a solid performer, and since its release, there have been minimal changes until now! Everything learned from the DBXL-E and DBXL-E 2.0 has directly been applied to the new and improved Losi® DBXL 2.0 4WD Gas RTR buggy. Built big and bold to deliver high-impact excitement, the DBXL 2.0 makes its presence known with a roaring new Zenoah® 32cc engine. A new high-flow air filter allows the engine to breathe to create maximum horsepower. This Losi 1/5th scale buggy powerhouse is designed to withstand the rigors of intense off-road driving with a full-time 4WD 5mm drivetrain, gearboxes, and heavy-duty construction that pulverizes the terrain at ballistic speeds. A brand-new steering rack and servo saver assembly keep your 2.0 tracking straight over any environment. A new radio tray, receiver box, and HV-rated servos take your DBXL 2.0 to the next level of performance. The DBXL 2.0 is also in for the long haul with a large-capacity tank for extended run times. The Losi DBXL 2.0 4WD Gas RTR is large-scale RC driving excitement at its most satisfying.Features Full 4WD drivetrain Pull Start Zenoah® G320 32cc 2-stroke gasoline engine Spektrum 3-channel SLT3 radio system Machined ring and pinion gear 800cc gas tank Integrated adjustable servo saver 4mm aluminum chassis Dual disk brakes Sealed differentials Icon Vehicle Dynamics and Magnaflow Liveries Zenoah® G320 32cc 2-stroke Gasoline EngineNew larger 32cc engine will provide the heart-pounding thrills you come to expect from a gasoline-powered engine. More displacement means more horsepower and more fun! New Center Pinned Outdrive CupsThe center drive cups have been redesigned so that they are now a ring captured design like the 5IVE-T, reducing the chances of drivetrain failures. 5mm Drive PinsTo put the power to the ground, we have increased the size of the outdrives and drive pins in all the dogbones to 5mm. They are still replaceable but now provide you the added strength and durability for the increased horsepower. Updated Gear BoxesProven on the DBXL-E 2.0, the gearboxes are now secured to the bulkheads with two screws to keep them from rocking up and down when power is applied. The gearboxes also allow for a more secure closure to better keep the pinion gear in place for increased strength and durability. Updated Steering Rack and Servo SaverUpdated helical design adds strength while providing a much smoother servo saver action for increased servo durability. Aluminum Shock Towers6mm thick Aluminum Front and Rear Shock Towers. Not only do these shock towers add durability/tunability to the DBXL 2.0, but they also add more tuning options to dial in your ride. Updated Shock BodiesUpdated shock bodies with a new lower aluminum cap allow for easier maintenance when changing out the shock O-rings. Updated Servo TrayNew servo tray allows you to run single or dual 1/5 scale steering servos as well as simplifying the throttle/brake linkage of easier tuning and adjustments. Updated Sway Bar LinksUpdated, larger, stronger sway bar links for added durability. New Chassis BracesNew dual rear chassis braces and torque rod increase chassis stiffness and durability Chassis Stiffening Plate4mm chassis stiffening plate under the engine allows for the use of engine slugs to set the gear mesh and reduce the chances of engine movement during large impacts. New Gas TankNew larger gas tank provides increased run time and a standard thread gas cap. New Center Differential Mount and Brake AssemblyConventional center differential mount allows for faster front and rear brake adjustments for improved handling. Authentic Motorsports Race Themed LiveriesMagnaflow Exhaust and Icon Vehicle Dynamics liveries LiPo Receiver PackThe included rechargeable 4000mAh 2S 7.4V Smart LiPo Receiver Battery allows for hours of playtime without stopping to re-charge Spektrum SLT3 Transmitter with Dual Protocol ReceiverA great low-cost radio system for bashers, crawler fans, and first-time drivers, the Spektrum 3-channel SLT3 with SR315 receiver goes beyond basic offering dependable SLT 2.4GHz control now, plus next-level DSMR® upgrade potential for the future. In The Box (1) DBXL 2.0 4WD Gas RTR (1) Spektrum SLT3 Transmitter with Dual Protocol (1) 4000mAh 2S 7.4V Smart LiPo Receiver Battery (1) Zenoah® G320 32cc 2-stroke gasoline engine (4) AA Batteries (1) User Manual (1) Miscellaneous Tools