FG Fun Cross WB535 Buggy 4WD HT-Edition
Product number:
fg_670060_ht
EAN:
4058575071464
Product information "FG Fun Cross WB535 Buggy 4WD HT-Edition"
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact.
The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.
The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable.
Equipment of the model:
Dimensions:
The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.
You can select the car with complete RTR-equipment from the options menu.
RTR-equipment
RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed.
- Transmitter: Reflex Wheel Pro III 2,4 GHz
- Receiver: Mini BEC
- High power servo for throttle and brake
- Largescale servo for steering
- Tx-battery, rx-battery
The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable.
| HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. | |
| Steel pinions - Non-standard sizes Each of two different ratios are supplied with.Modul: m=1,5 Value: 62,60 EUR |  |
| Alloy engine mount small CNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant. Value: 54,90 EUR |  |
| Driveshaft boots Protect ball drive as well as cardan drive against dirt. 4 pairs / 8 pieces Value: 42,90 EUR |  |
| Alloy spur gear carrier Use for 46T - 48 teeth spur gears. Value: 39,90 EUR |  |
| Total value: 200,30 EUR | |
Equipment of the model:
- Powerful 26 cm³ engine
- Two differentials
- 4 mm thick chassis
- Four wheel independent suspensions
- Big Bore dampers
Dimensions:
- Length: 700 mm
- Width: 460 mm
- Height: 310 mm
- Wheelbase: 535 mm
- Weight: 10,4 kg
Login
Similar products
Ready for an extra portion driving fun? Then try the FG Monster Buggy Pro! This aggressive looking model based on the Fun Cross chassis is extremely fast, easy to handle and very pleasant to drive. A complete package of well-tried racing technology! The model will be delivered with a clear body shell.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURPowerful 26 cm³ petrol engineMaintenance friendly chassis2 Differential gearsHardened driving partsCompletely ball-bearingedLarge-volume alum. dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure funThe model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.Measures:Length: 715 mmWidth: 495 mmHeight: 360 mmWheelbase: 535 mmWeight: 10,4 kg
Ready for an extra portion driving fun? Then try the FG Monster Buggy Pro! This aggressive looking model based on the Fun Cross chassis is extremely fast, easy to handle and very pleasant to drive. A complete package of well-tried racing technology! The model will be delivered with a clear body shell.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.Powerful 26 cm³ petrol engineMaintenance friendly chassis2 Differential gearsHardened driving partsCompletely ball-bearingedLarge-volume alum. dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure funThe model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.Measures:Length: 715 mmWidth: 495 mmHeight: 360 mmWheelbase: 535 mmWeight: 10,4 kg
Ready for the ultimate Off-Road fun? Four-wheel drive combined with well-tried competition technology in an affordable beginner model. With the Sportsline Leopard 4 you purchase a premium RTR Racing Buggy manufactured of top-quality materials with the potential to win races - completely assembled and ready for racing. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The lateral splash-guard and the almost closed bodyshell prevent engine, servos a.s.o. from dirt. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries, either with painted or clear bodyshell. To complete the non-RTR version with clear bodyshell all popular servos and radio control systems are suitable.Dimensions:Length: 750 mmWidth: 470 mmHeight: 330 mmWheelbase: 534 mmThe video shows the FG-Marder in terrain!
Der neue Allrad-Wettbewerbsbuggy Leo 3 ist mit drei Differenzialen ausgestattet. Diese neue Version ist von den 1/8 Wettbewerbsbuggys inspiriert. Durch die sehr direkte Kraftübertragung wird mehr Leistung generiert. Die Zentralbremse ist im Differential- Bock integriert. Das Modell ist mit einem Chassis aus gefrästem 5 mm T7075-Aluminium, großvolumigen Stoßdämpfern, ein Resonanzschalldämpfer und einer neuen aerodynamischen Karosserie ausgestattet. Der Motor (separat zu erwerben) wird in der Mitte mit einer Neigung zur Optimierung des Schwerpunkts eingebaut. Die Wartung dieses Modells wird durch einen schnellen Ausbau der einzelnen Teile erleichtert. Das Modell wird ohne Motor, Kupplung, Airbox und RC-Anlage geliefert.Abmessungen : Länge : 770mm Breite : 470mm Hohe : 330mm Radstand : 580mm Gewicht : 13.2kgNicht inbegriffen : Motor 26cc, 29cc Kupplung Airbox RC-Anlage
Ready for the ultimate Off-Road fun? Four-wheel drive combined with well-tried competition technology in an affordable beginner model. With the Sportsline Leopard 4 you purchase a premium RTR Racing Buggy manufactured of top-quality materials with the potential to win races - completely assembled and ready for racing.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The lateral splash-guard and the almost closed bodyshell prevent engine, servos a.s.o. from dirt. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EUR The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries, either with painted or clear bodyshell. To complete the non-RTR version with clear bodyshell all popular servos and radio control systems are suitable.Dimensions:Length: 750 mmWidth: 470 mmHeight: 330 mmWheelbase: 534 mmThe video shows the FG-Marder in terrain!
The FG Off-Road Buggy WB535 4WD is presented with a longer wheelbase and a pleasant design. Are you setting value on a well-blanced driving performance with quarantees enough grip and driving fun as well as on functionality and visual appearance? Then the new Off-Road Buggy WB535 is your best choice. Painted body shell to choose, all-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body painted either finished or unpainted. The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. Additionally the 4WD grants the model the maximum driving power and highest fun factor on every surface and in all curves.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURAccording to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg
Ready for an extra portion driving fun? Then try the TR4 made by FG! Agressive appearance combined with the Leopard 4 chassis results in an optimal handling and stunning top speed with lots of driving fun wich will thrill you. Equipped with a 26 cm³ two-stroke gasoline engine with installed pull-start system. The TR4 is an uncomplicated complete package with well-tired racing technology.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical information:Strong 26 cm³ gasoline engineMaintenance friendly chassisTwo differential gearsHardened driving partsCompletely ball-bearedLarge-volume aluminium dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure driving funHT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURDimensions: Length: 760 mm Width: 520 mm Height: 320 mm Wheelbase: 534 mm
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. Equipment of the model:Powerful 26 cm³ engineTwo differentials4 mm thick chassisFour wheel independent suspensionsBig Bore dampersDimensions:Length: 700 mmWidth: 460 mmHeight: 310 mmWheelbase: 535 mmWeight: 10,4 kg
The FG Off-Road Buggy WB535 4WD is presented with a longer wheelbase and a pleasant design. Are you setting value on a well-blanced driving performance with quarantees enough grip and driving fun as well as on functionality and visual appearance? Then the new Off-Road Buggy WB535 is your best choice. Painted body shell to choose, all-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body painted either finished or unpainted. The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. Additionally the 4WD grants the model the maximum driving power and highest fun factor on every surface and in all curves.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg
Ready for an extra portion driving fun? Then try the TR4 made by FG! Agressive appearance combined with the Leopard 4 chassis results in an optimal handling and stunning top speed with lots of driving fun wich will thrill you. Equipped with a 26 cm³ two-stroke gasoline engine with installed pull-start system. The TR4 is an uncomplicated complete package with well-tired racing technology.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical information:Strong 26 cm³ gasoline engineMaintenance friendly chassisTwo differential gearsHardened driving partsCompletely ball-bearedLarge-volume aluminium dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure driving funDimensions: Length: 760 mm Width: 520 mm Height: 320 mm Wheelbase: 534 mm
Customers also viewed
Ready for the ultimate Off-Road fun? Four-wheel drive combined with well-tried competition technology in an affordable beginner model. With the Sportsline Leopard 4 you purchase a premium RTR Racing Buggy manufactured of top-quality materials with the potential to win races - completely assembled and ready for racing.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The lateral splash-guard and the almost closed bodyshell prevent engine, servos a.s.o. from dirt. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EUR The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries, either with painted or clear bodyshell. To complete the non-RTR version with clear bodyshell all popular servos and radio control systems are suitable.Dimensions:Length: 750 mmWidth: 470 mmHeight: 330 mmWheelbase: 534 mmThe video shows the FG-Marder in terrain!
The FG Off-Road Buggy WB535 4WD is presented with a longer wheelbase and a pleasant design. Are you setting value on a well-blanced driving performance with quarantees enough grip and driving fun as well as on functionality and visual appearance? Then the new Off-Road Buggy WB535 is your best choice. Painted body shell to choose, all-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body painted either finished or unpainted. The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. Additionally the 4WD grants the model the maximum driving power and highest fun factor on every surface and in all curves.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURAccording to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. Equipment of the model:Powerful 26 cm³ engineTwo differentials4 mm thick chassisFour wheel independent suspensionsBig Bore dampersDimensions:Length: 700 mmWidth: 460 mmHeight: 310 mmWheelbase: 535 mmWeight: 10,4 kg
This 1/6 scale 4WD Off-Road buggy has been strongly inspired by competition types. With its front and rear Leopard type suspensions, the Fun Cross allows the most extreme drives. Built on a 4mm aluminium chassis, closed belt drive, 2 differential gears, double wishbones at front and rear axle with many adjusting possibilities as well as large-volume oil-pressure shock absorbers for traction and optimal ground contact. The model is equipped with a powerful 26 cm³ combustion engine with tuning pipe and ready oiled air-filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version is delivered with assembled and preset 2.4 GHz radio control system and rechargeable batteries. To complete the non-RTR version are all popular servos and radio control systems are suitable. HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURPowerful 26ccm engine with integrated pull-rope starter running with 2 stroke petrol mixturechassis with side protections.Four-wheel independent suspension with numerous adjustment possibilities.Adjustable long stroke Big Bore dampers.Hardened steel transmission on ball bearings.Protection cage can be used as a transport handle.Fully enclosed polycarbonate body, painted and decorated.Nylon rear spoiler with adjustable incidence.Installed and glued spike tires.Dimensions :Length: 770 mmWidth: 465 mmHeight: 300 mmWheelbase: 535 mmWeight: 9,1kg Contents:1 piece
The FG Off-Road Buggy WB535 4WD is presented with a longer wheelbase and a pleasant design. Are you setting value on a well-blanced driving performance with quarantees enough grip and driving fun as well as on functionality and visual appearance? Then the new Off-Road Buggy WB535 is your best choice. Painted body shell to choose, all-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body painted either finished or unpainted. The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. Additionally the 4WD grants the model the maximum driving power and highest fun factor on every surface and in all curves.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg
With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.