FG Electric 4WD Truggy TR4E WB535, ESC 150A and Brushless Motor 6S

The vehicle is being sold as used on behalf of a customer.  The original price is 1339 euros! The FG TR4E Truggy 4WD has only been run for 10 minutes and is in as good as new condition !  It is delivered without transmitter set.  A powerful 55KG steering servo provides sufficient steering power.  A TopTuning 700KV 4 pole brushless motor and a 200A Beast Pro speed controller are installed. You need a transmitter set, 2x4S batteries and a charger, then you're ready to go.  Take a look at the photos. No matter where you perform with it and where you use it - with the FG TR4E you will be at the front of the pack!  The E stands for electric power, the 4 for all-wheel drive. Extremely fast, powerful torque and all without noise. The TR4 is equipped with a powerful brushless motor and a controller.  The electric power means extremely high torque, high top speed and all without engine noise. The Sportsline models are equipped with a powerful brushless motor and a brushless controller. Thanks to the built-in all-wheel drive, the models can be easily manoeuvred through any terrain without getting stuck.  The controller can be easily adjusted via the transmitter or optionally via a programming card. 

No matter where you will set this model into action - you will always be right in front with the FG Leopard 4E! No matter where you take it and where you use it - with the FG Leopard 4E you will be at the forefront! The E stands for electric power, the 4 for all-wheel drive. Extremely fast, a powerful torque and all without noise. The model is equipped with a powerful brushless motor and a controller. The Vehicle is supplied with white painted bodywork and decal sheet. The E stands for Elektro-Power and means extremely high torque, high top speed and all without engine noise. The Sportsline models are equipped with a powerful brushless motor and a brushless controller. Thanks to the built-in all-wheel drive, the models can be easily manoeuvred through any terrain without getting stuck. The controller can be easily adjusted via the transmitter or optionally via a programming card.You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. The control can be regulated simply via transmitter or optionally via a program card. For the final assembling you need LiPo batteries and the suitable charger. For an unproblematic mounting we recommend to use LiPo batteries with a max. length of 150mm and a width of 50mm. The model is delivered with the EC8 connector system.

The FG Off-Road Buggy WB535E - now with brushless power! No matter where you take it and where you use it - with the FG Off-Road Buggy you will be at the forefront! The E stands for electric power, the 4 for all-wheel drive. Extremely fast, a powerful torque and all without noise. The model is equipped with a powerful brushless motor and a controller.  The E stands for Elektro-Power and means extremely high torque, high top speed and all without engine noise. The Sportsline models are equipped with a powerful brushless motor and a brushless controller. Thanks to the built-in all-wheel drive, the models can be easily manoeuvred through any terrain without getting stuck. The controller can be easily adjusted via the transmitter or optionally via a programming card.You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed.The control can be regulated simply via transmitter or optionally via a program card. For the final assembling you need LiPo batteries and the suitable charger. For an unproblematic mounting we recommend to use LiPo batteries with a max. length of 150mm and a width of 50mm. The model is delivered with the EC8 connector system.

No matter where you will set this model into action - you will always be right in front with the FG Monster-Truck 4E! The E stands for electric power, the 4 means fourwheel drive. Extremely fast, terrific torque and all this without any engine noise. The Model is equipped with a powerful Brushless Motor and a ESC.You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. The control can be regulated simply via transmitter or optionally via a program card. For the final assembling you need LiPo batteries and the suitable charger. For an unproblematic mounting we recommend to use LiPo batteries with a max. length of 150mm and a width of 50mm. The model is delivered with the EC8 connector system.Dimensions:Length: 710 mmWidth: 510 mmHeight: 390 mmWheelbase: 535 mm

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

18mm wheel square, 17mm wide.Bore diameter 8 mm

Tools and decorative items are for presentation purpose only and not included. Genuine HT spare/option part. Tool bag, extremely rugged tool bag made from reinforced fabric, sewn edge. With 41 flexible attachment loops for various tools with all-round zipper and reinforced handle.Dimensions:Width: 510 mm Height: 275 mmContents:1 piece