The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.
High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!
Genuine FG spare/option part. Black fuel hose 3x6 mm also suitable for the tank ventilation. Softness approx. 60 shore. Suitable for all big scale models.
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.
Genuine HT spare/option part. Fuel filter to be installed in the fuel line outside of the tank. Dimensions of filter body: 32 x 21 x 17 mm.Contents:1 piece
6 litre gas can with thumb activated filler valve.With Rapido filling up is quicker, simpler and more convenient than ever! Thanks to the dosing button you can control the flow of fuel precisely.Unlock by folding out!Press the button and keep control of filling!Lock by folding in again. Finished!No spills, no awkward handling, all clean and easy Other:Half round spout for ventilation and visibility suitable also for the smallest tank openingsLarge opening for easy fillingFlow controlled by press-buttonVentilation allows full flowSturdy design with two handlesTransparent 6 litre container with litre indication in the filling and rest positionsContents:1 piece
Genuine FG spare/option part. Plastic tank bottle, fuel resistant, with angled alloy filler tube, volume 500 ml. For a faster refueling of the models.Contents:1 piece
This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
Suitable for all FG/Carson/Smartech cars except FG Evo and Carson 4WD.Please note that tank mount 7143 is required for installation. Installation in a Carson/Smartech 1/6 off-road car requires drilling of two new 4.5 mm diameter holes into the chassis plate. Drilling template is included.Comes as shown with fuel lines, grommet and gas cap included.
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).