B59011 Rear uprights, set with pins and bearings

BWS

€39.90*

Prices incl. VAT plus shipping costs

Available

Product number: b_59011

Product information "B59011 Rear uprights, set with pins and bearings"

Dimensionally identical with Losi 5ive part LOSB2077 / LOSB2080 / LOSB2072 / LOSB5971 / LOSB5972.

Contents:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Alternatives

LOSB2077 Losi Rear Hub Carrier Set 5T, TLR 5ive-B and Mini

Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini.Dimensionally identical with B59011Content:2 pieces

€19.99*

This product is currently not available.

LOSB2080 Losi Hinge Pin Set 5T and Mini

Fits Losi 5ive-T and 5ive Mini.Dimensionally identical with B59011Contents:6 pieces

€29.99*

This product is currently not available.

LOSB5971 Losi Inner Axle Bearings, 20 x 32 x 7 mm, Losi 5ive-T/2.0, TLR 5ive-B and Mini WRC

Genuine Losi spare/option part. Fits Losi 5ive-T, TLR 5ive-B and Mini WRC.Dimensionally identical with B59010 / B59011Content:2 pieces

€19.99*

LOSB5972 Losi Outer Axle Ball Bearings sealed, 12 x 24 x 6 mm, Losi 5ive-T/2.0, TLR 5ive-B and Mini WRC.

Fits Losi 5ive-T, TLR 5ive-B and Mini WRC.Dimensionally identical with B59010 / B59011.Content:2 pieces

€9.99*

Kunden haben auch gesehen

B59010 Spindles and c-hubs, set with bearings and king pins

Dimensionally identical with Losi 5ive part LOSB2073 / LOSB2072 / LOSB2072 / LOSB5971 / LOSB5972.Contents:1 set

€49.90*

This product is currently not available.

ST-EWP31D SPEED TEC 0,30 mm Insulator gasket G320RC gasket EWP207

Genuine Speed-Tec spare/option part. EWP207 is a gasket material based on NBR-bonded synthetic and organic fibres. It therefore has very good oil and fuel resistance and does not swell like other gaskets.EWP207 is ideally suited for sealing against cold and hot oils, greases and fuels. Features Oil resistant Heat repellent Does not swell Contents:1 piece

€5.30*

FG Challenge Line 510 Mini Cooper with 26 cm³ FG engine

With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm

Variants from €849.90*

€969.80*

Configure now

y3008 Pulse beat decal sheet with pinstripe trim, choice of colors

Genuine HT spare/option part. Pulse beat decals with pinstripe trim for body shell decoration. The pulse beat decals have a total length of about 395 mm, a height (measured at the highest peak) of about 90 mm and a line width of 5 mm. The pinstripe trims are about 395 mm long by 5 mm wide.Colors available:y3008/01 - Greeny3008/02 - Orangey3008/03 - Bluey3008/04 - Redy3008/05 - Pinky3008/06 - BlackContents:1 piece

€9.90*

y0767 Electronic 20 Amp Bigscale high voltage 30 Volt switch

The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1000SGT servo and 4s receiver battery y1304. Note: the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VMax. Load: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 28 mm Width: 12 mmHeight: 11 mm

€49.90*

67299/03 FG Aluminum exhaust mount 4WD, set

Item N° 67299/03Aluminum exhaust mount 4WD, setRugged aluminum exhaust mount for the Leopard 4WD Competition car. Replaces the exhaust installation using piano wires.

€32.90*