Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

AT-DBXL 015 ATOP Lower front- and rear alloy a-arms for Losi Desert XL/XL-E / 2.0

Product information "AT-DBXL 015 ATOP Lower front- and rear alloy a-arms for Losi Desert XL/XL-E / 2.0"

Genuine ATOP spare/option part.

CNC-machined 6061-T6 aluminum suspension arms for Losi DBXL.

Set of four a-arms with plastic bushings for the hinge pins, all required nuts and bolts are included.

Contents:
  • 2 pieces

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

AT-DBXL028 ATOP Aluminum rear uprights for all Losi DBXL/MTXL
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces

€79.90*

Average rating of 0 out of 5 stars

AT-DBXL001 ATOP Alloy spring retainer for Losi DBXL/XL-E +MTXL shocks
Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces

From €16.90*

Average rating of 0 out of 5 stars

AT-DBXL002 ATOP aluminum camber rods/steering rods for Losi DBXL/DBXL-E
Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces

€34.90*

Average rating of 0 out of 5 stars

AT-DBXL022 ATOP Aluminum rear transmission mount for Losi DBXL/DBXL-E/2.0 + MTXL
Genuine ATOP spare/option part. Rear transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!

€79.90*

Average rating of 0 out of 5 stars

AT-DBXL002/01 ATOP Spacer bushings for camber/steering rods of Losi DBXL and DBXL-E
Genuine ATOP spare/option part. Aluminum spacer bushings for the ball joints on camber and steering rods of Losi DBXL and DBXL-E.Content:8 pieces

€9.80*

Average rating of 0 out of 5 stars

AT-DBXL020 ATOP Complete Aluminum transmission case front / rear for Losi DBXL/DBXL-E/2.0 + MTXL
Genuine ATOP spare/option part. CNC-machined 6061 aluminum transmission case by ATOP, fits front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!

€139.90*

Average rating of 0 out of 5 stars

y0057 Ball & socket tool for Losi and HPI
Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

AREA-XL 008/01 Spare O-rings
Genuine Area spare/option part. Spare part for AREA-XL 008 Wheel spacer for using the 5ive-T and HPI wheels with the Losi Desert XL.The O-rings are used as additional retainers fort he drive pins.Content:4 pieces

€4.90*

Average rating of 0 out of 5 stars

AT-DBXL009/010 ATOP Front and rear shock tower for Losi Desert XL/XL-E +MTXL
Genuine Atop spare/option part. CNC-machined 6061-T6 aluminum shock towers for Losi DBXL. Direct replacement for the stock part.Contents:2 piece

€119.90*

Average rating of 0 out of 5 stars

AT-DBXL016 ATOP aluminum steering rods for Losi DBXL-E 2.0
Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces

€34.90*

Average rating of 0 out of 5 stars

HR1001/01 Spare parts set for HR-Creations Losi DBXL a-arms
Replacement part for the front and rear wishbone set with the order number: HR1001.Set includes:4 x bushing4 x flanged bushing2 x droop limiter screw2 x locking nut2 x lock washer4 x Locking screw for hig pin

€7.90*

Average rating of 0 out of 5 stars

AT-DBXL011 ATOP Complete Aluminum transmission case for Losi DBXL/DBXL-E + MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum transmission case by ATOP for Losi DBXL/DBXL-E and MTXL, front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case.Contents:1 piece

€149.90*

Customers also viewed

Average rating of 0 out of 5 stars

LOS252021 Driveshaft rear center Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!

€59.99*

Average rating of 0 out of 5 stars

AT-DBXL011 ATOP Complete Aluminum transmission case for Losi DBXL/DBXL-E + MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum transmission case by ATOP for Losi DBXL/DBXL-E and MTXL, front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case.Contents:1 piece

€149.90*

Average rating of 0 out of 5 stars

AT-DBXL033 ATOP Aluminum center differential towers for Losi DBXL 2.0
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum center diff mount; fits Losi DBXL 2.0.4-piece set consisting of two diff towers, connecting bridge, and pinion cover. Considerably stiffer than the standard plastic parts and unaffected by the heat generated by the engine and the brake.Contents:1 piece

€149.90*

Average rating of 0 out of 5 stars

y1340 Adjustable wing mount with wing for Losi Desert Buggy XL, DBXL-K&N
Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal

€79.90*

Average rating of 0 out of 5 stars

y0045 GPM Crankcase cover for 1/5 & 1/6
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape

€24.90*

Average rating of 0 out of 5 stars

y1388 Offroad tuning springs Dirt-Spring DBXL/XL-E +MTXL
y1388 Version: y1388/02 - 2,6 x 110 mm Blue, 1 pair
Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/08 - Complete set, unit prices: 132,93 EUR 

€21.99*

Average rating of 0 out of 5 stars

GPM SLO5T 16/18/20/21 steel pinion incl. washer for Losi 5ive-T, 5ive-B and Mini
gpm_slo5t Teeth: SLO5T018T - 18 teeth
Hardened steel pinion set for Losi 5ive-T, 5ive-B and Mini, with corresponding engine mount inserts included. All parts with laser etched tooth count.Please note: The pinion do fit the 5ive-T 2.0 as well, of course. However, you then have to use the 5ive-T 2.0 engine mount inserts of the appropriate tooth count, inserts from the 5ive-T do not fit! Available with 16, 18T/20T/21T. The 19T pinion is stock equipment in Losi 5ive-T and Mini, 20T is stock in the 5ive-B.The 16T pinion is profile shifted and has the same dimensions as a normal 18T pinion.It is specially made for vehicles where the stock tires are replaced by much larger diameter rubber (i.e. monster truck tires and MadMax Giant Grip).Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter.SLO5T018T replaces LOSB5046 and LOSB5805SLO5T019T replaces LOSB5044 and LOSB5801SLO5T020T replaces LOSB5045 and LOSB5802The higher the tooth count, the higher the top speed!

€39.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency