Product information "AREA BJ009 Aluminum engine mount brace Baja 5"
Genuine Area spare/option part.
Aluminum l/h rear engine mount brace for all cars of the HPI Baja 5 series. Utilizes both engine mounting holes and stiffens the corresponding section of the chassis structure.
Please note: does not fit in combination with Zenoah G320 engine.
Contents:
1 piece
0 of 0 reviews
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Cylinder-piston repair kit for 23 cm³ HPI-Fuelie engine. The set includes the following parts:Cylinderpistonpiston ringcylinder foot gasketpiston pin clipAttention: The set is 100% identical to the Zenoah set no. Attention: The set is 100% identical to the Zenoah set no. 7387Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
The Tarmac Buster tires are the ticket for asphalt, concrete, or even hard packed clay. Molded in HPI?s exclusive M Compound, the Tarmac Busters have an aggressive street tread pattern that delivers outstanding grip on the street. Sold in pairs, these tires are a direct replacement for the factory Baja 5B tires. You need the same tire insert as for the stock tires.
Regular price Big Scale Clutch: 109,90 EUR Nitriding hardened clutch bell: 40,50 EUR complete price:.......................150,40 EURAdjustable 3-shoe clutch for:Zenoah / Chung Yang / HPI - Fuelie / Smartech PT and many other engines.The delivery content:- y0730 GPM Big Scale-Cross adjustable 3 shoe clutch, 1 pce. - y0729 Gas-nitrited tuning clutch bell for HPI Baja, 1 pce. The Gas-nitrited tuning clutch bell:Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding. Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch. Suitable for genuine slot drive HPI pinions. Comes with bolts and spring washers included.The GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Handling instructions for three-shoe clutches y0730 GPM Big Scale Cross and y0731 GPM Big Scale RaceInstallation:The GPM Big Scale clutch will be bolted to the crankshaft using the supplied CSH-screw.It should be noted that the use of thread locking compound on that screw is neither necessary nor recommended!Removal:Remove the CSH-screw with a 4mm Allen wrench; then insert a suitable M8 bolt and remove the clutch from the crankcase cone by tightening that bolt. Hole for adjustment:For clutch adjustment without removing the clutch bell a 4 4.5 mm hole must be drilled into the clutch bell for access to the adjustment screw. Placement of the hole depends on clutch bell dimensions and car; so you have to make your own measurements for the placement of the hole.It is important that the drilled hole is thoroughly deburred (at least on the inside of the clutch bell) to prevent excessive clutch pad wear. Breaking in:A new clutch or shoes fitted with new pad should always be broken in. Therefore the clutch engagement speed should not be too high for the first tank of fuel. This gives the lining the possibility to adjust to the clutch bell without glazing. The only difference between two clutches is the clutch spring rate, which provides the optimal range for clutch engagement depending on the application. The three available versions of clutch springs provide adjustability within the following RPM ranges:Silver springs 1.3 mm y0730/05 (standard on Big Scale Cross): 5,000 9,500 RPMGold springs y0730/06 1.4 mm (standard on Big Scale Race): 6,500-11,500 rpm Adjustment:Adjustment of the clutch engagement speed is done by one single screw using a 2.5 mm Allen wrench. Turning the screw in increases the stall speed, backing it out will lower the stall speed. The adjusting screw is thread locked to keep the setting. Should you realize that the screw can be turned too easily please re-apply medium strength thread locking compound.Finding the best clutch engagement speed:The best clutch engagement speed should be found while driving on the track, it depends on engine characteristic, track layout, track surface and driving style.It is recommended to start with the lowest setting (which means the set screw just touching the adjustment cam) and gradually turning the adjusting screw in while doing test runs after every adjustment.If you feel that you have exceeded your best engagement speed (clutch will slip too much), back the screw out for a little bit to avoid excessive wear or glazing of the pads.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!
Genuine FG spare/option part. Made from T7075 aluminum with wide epoxy insulator plates to protect against engine heat transfer. Venturi-shaped bore increases engine performance.For easier installation removing the cylinder shroud is recommended .Contents:1 Set
Genuine AREA spare/option part.Spare brake pads for AREA front disc brake AREA-BJ029 Front disc brake for HPI Baja 5 models, machined from billet 7075-T6 aluminum.Contents:1 piece
€39.90*
This website uses cookies to ensure the best experience possible. More information...