8106 FG BBS wheel white 65mm, 2pcs
€19.90
Currently unavailable
Product information "8106 FG BBS wheel white 65mm, 2pcs"
Login
Customers also bought
With this adapter you get all the major solo air boxes mounted on her solo motor.
Genuine FG spare/option part. FG ball bearing with heat resistant grease filling up to 180°. Therefore essentially improved durability of the wheel bearings and the clutch bell.For all FG cars with alloy differential case except 4WD and Formula 1.Contents:Eight pieces: 8 x 22 x 7 mmTwo pieces: 10 x 22 x 6 mmTwo pieces: 10 x 19 x 7 mmTwo pieces 15 x 28 x 7 mm
Customers also viewed
1 pair of white BBS rims with 18mm square for Onroad. Diameter 95mm Width 65mm. See photos for condition and scope of delivery.
Genuine FG spare/option part. Detailed BBS wheels in colour white. Rim with 18 mm square driveDimensions:Narrow version in 65mm widthDiameter of the wheels: 95mmContent:2 pieces
Suitable for all FG 1:5 models and other makes.Rim with 18 mm square driveRim width: 65mmRim diamter: 95mmColour: White
Mammoth Supergrip onroad 60 and 80 mm tires on white FG rims complete glued, 1 pair.Mammoth Supergrip onroad tires on FG rims for 1/6 and 1/5 offroad cars.Suitable for asphalt surfaces such as car parks and race tracks. Racing tyres for your off-road model.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings outside ), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURPrices Total 85,80 EUR 105,70 EUR
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³. incl. clutch spring!Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!