Genuine FG spare/option part. Dimensions: Decal 1 (main decal): approx. 500 x 300 mm Decal 2 (window decal): approx. 320 x 430 mm Decal 3 (window decal blue): approx. 250 x 85 mm Decal 4 (light decal): approx. 110 x 20 mm Contents:1 set
Genuine HT spare/option part. For all epoxy models, plastic and polycarbonate/lexan body repairs!Direction of use:Use a brush or other applicator. Apply enough Flexa Fix to the damaged area. Be careful not to apply too much in one go as it can be difficult to manipulate. If necessary apply two or three coats to build up the joint area. Use epoxy blanket of pieces of polycarbonate (Lexan) to re-enforce if necessary.You can also use the Flexa Fix to re-enforce the body corners (let the pure product leak into the corners) or to make flexible battery packs.Contents:1 piece / 100 ml
The body shell is neither cut nor drilled, clear and can therefore be adopted to all touring cars with a 510 mm wheelbase. Set includes Rear Wing. Dimensions: Length: ca. 900 mm Width: ca. 370 mm Height: ca. 250 mm Required body mounts: Front bumper: 7020/16 and 7011/01 Front side: 8013 Rear side: 3014 Rear mount: 2x 7152/01 and 1x 7153 Contents:1 piece
Genuine FG spare/option part.The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The thickness of the body shell is 2.0 mm and fits for Sportsline models. The body shell is vac-formed from 2 mm Lexan.The set is delivered unpainted.Frontteil: 5172 FG Porsche GT3 RSR body, front sectionHeckspoiler: 5173 FG Spoiler set Porsche GT3 RSR transparentRequired body mounts:Mount front: Rear body mount: Side body mount front: Side body mount rear: Measures:Length: 890 mmWidth: 405 mmHeight: 240 mmWheelbase: 510 mmPainting tips:
Genuine FG spare/option part. The body kit consists of the main body part and partial front and rear spoiler. The body is unpainted. The body shell is vac-formed from 2 mm Lexan.Required body mounts:Mount front: FG 7020/11 Front bumper Side body mount front: FG 7012 Body mounts Side body mount rear: FG 3014 Body mounts Rear body mount: FG 7155 Rear body mountDimensions:Length: 780 mmWidth: 392 mmHeight: 280 mmWheelbase: 510 mmContents:1 piece Painting tips:
Genuine FG spare/option part. The body kit consists of the main body part and partial front and rear spoiler. The body is unpainted. The body shell is vac-formed from 2 mm Lexan.Required body mounts:Mount front: FG 7020/11 Front bumper Side body mount front: FG 7012 Body mounts Side body mount rear: FG 3014 Body mounts Rear body mount: FG 7155 Rear body mountDimensions:Length: 780 mmWidth: 392 mmHeight: 280 mmWheelbase: 510 mmContents:1 piece Painting tips:
Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm
Genuine FG spare/option part.The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The thickness of the body shell is 2.0 mm and fits for Sportsline models. The body shell is vac-formed from 2 mm Lexan.The set is delivered unpainted.Frontteil: 5172 FG Porsche GT3 RSR body, front sectionHeckspoiler: 5173 FG Spoiler set Porsche GT3 RSR transparentRequired body mounts:Mount front: Rear body mount: Side body mount front: Side body mount rear: Measures:Length: 890 mmWidth: 405 mmHeight: 240 mmWheelbase: 510 mmPainting tips:
Lighter, for weight-reducing reasons manufactured 1.5mm polycarbonate bodyshell. The set includes: 1.5mm F1 bodyshell, body front and side parts 2mm. The body shell is vac-formed from 1,5 mm Lexan.The set is delivered unpainted.Painting tips:
PMT tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine PMT spare/option part. The Supreme have been designed for all track conditions. Developed with latest generation components, deriving directly from the highest level of Motorsport, they are available in three hardnesses:SS "NEW": supersoft, 35 shore hardness, suitable for rear and slightly abrasive asphaltsS00 (K00): soft, 38 shore hardness, suitable for rear and slightly abrasive asphaltsM00/P1 (K01): medium, 42 shore hardness, suitable for rear / front and medium abrasive asphaltsH00/P1 (K03): hard, 45 shore hardness, suitable for front and very abrasive asphaltsOn this type of tyres a new lighter and harder rim will be used, designed to withstand 25% higher lateral forces, compared to existing ones.Moreover, even the filling mousse has been updated and can now withstand up to a temperature of 130 °, without altering its mechanical characteristics. Dimension: Outside diameter: approx. 116 mm Width: approx. 65 mm Rims: 18 mm square drive Contents:2 pieces
The first 1/5 touring and sports car designed as a 4WD from the ground up. With a wheelbase of 510mm the 4WD chassis is suitable for the FG Mini Cooper and the FG Porsche GT3 RSR bodies. Equipped with a strong 26 cm³ engine, tuning pipe, tank with quick acting closure, 2 differential gears, front disk brake and a lot more. However, the highlight is still the well-known FG 4WD. Maximum traction, easy handling and grip during cornering as well, these are the advantages only a 4WD model can offer.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The RTR version of the car includes servos, transmitter, receiver, rechargeable batteries for transmitter / receiver.The 4WD Sportsline chassis opens up a new era within the Touring and Sportscar class of large scale model cars. Main target was the development of a chassis with supreme driving dynamics and ultimate performance. Maximum traction as well as easy handling, sufficient grip in curves, only a fourwheel powered model offers all these advantages. With the new 4WD Sportsline series FG Modellsport once again sets a trend at 1:5 scale.The 4WD Sportsline chassis for the Porsche 911 GT3 RSR is delivered with a wheelbase of 510mm. The fourwheel drive is carried out over an almost wear resistant tooth belt. 2 differential gears, tank with snap closure and a powerful engine with Tuning pipe turn the Sportsline 4WD chassis into a high-class 1:5 scale model with outstanding driving characteristics.You can choose this 4WD model with painted bodyshell , 2.4 GHz radio control system, servos, batteries in our configurator. Team decals are not included in the delivery content and have to be ordered separately.The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problems. A tank filling enables you to run your model around 45 minutes. Equipment and technical description:Solid 4mm chassis made of high-quality aluminium low-wear belt drive splash-proved 2 differential gears double wishbones at front and rear axle toe-in, castor and wheel camber adjustable at the axles - rear FG ball drive all steel driving components hardened all rotating parts ball-beared servo relieving servo saver front disk brake rear gear brake with big brake disk 700ccm fuel tank with snap closure oil-pressure shock absorbers with volume control and spring adjusting ring 26 cm³ combustion engine with Tuning pipe fabric hollow chamber tires with inserts receiver box and battery holder polycarbonate bodyshell 2.4 GHz pistol grip radio control system with steering and gas servo.Dimensions: Length: 980 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURTouring cars in action!Painting tips:
The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Basic Kit of the FW01 is especially intended for "switchers" and differs from the chassis kit in terms of the brakes and shock absorbers (included in the chassis kit). Here is a list of the parts that are required for completion:brakes, shocks and springs (Difference to Chassis Kit)DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlStock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us!The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01.Included in the basic kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the engineDoes not include- Brakes, shocks and springs- differential- clutch- body and spoilers- Airbox- Engine and linkage- Electronics- Tires
€1,862.00*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).