7371 FG Plastic part and carburetor nipple

Genuine FG spare/option part.Standard carburetor for Zenoah G230/260. Carb has integrated choke.Typ: Walbro WT603B.Contents:1 piece

y0251 Performance carburetor with accelerator pump type: WT-813Walbro WT-813A carb with accelerator pump, improves low end response when the engine is tuned for maximum performance. 15.88mm bore, 12.7mm venturi. Ready for installation with modified shaft already installed. Fits Zenoah G230/240/260/270 engines and their CY/HPI Fuelie clones as well. Fits all Zenoah G230/240/260/270 and 290 engines as well as the respective Chung-Yang (CY) versions, also Losi and HPI Fuelie, Smartech, Carson PT engines, and many others.

Race ported top end set for Zenoah G260 engine.The SPEED TEC EXPERT genuine Zenoah G260 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionnlarged portsFuel management milledModified exhaust and intake Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome ground The set includes the following items: Performance-optimized cylinder and piston, piston ring, piston pin, piston pin circlips and cylinder gasket.To achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe ().

Reduced cross-section and flow-optimized transfer port cover plates for improved and faster gas flow for the Zenoah G320. The improved gas flow rate improves speed and gives faster throttle response in the medium rpm range. To improve mixture formation, the plates were glass bead blasted after machining.

With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.A roll cage was installed for more rigidity and protection of the vehicle.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURDimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm

Genuine FG spare/option part. This roll bar is just for looks, not for protection. It consists of aluminum tubes and plastic corner joints.Fits stadium truck body shells.Contents:1 set

Genuine Mielke spare/option part. Original replacement part for Mielke no 5705 plug tuning pipe.Contents:1 piece