6730/52 FG Grub screw with safety device M5x5mm Torx, 10 pieces

€3.20*

Prices incl. VAT plus shipping costs

Available

Product number: fg_6730_52

EAN: 3410564512050

Product information "6730/52 FG Grub screw with safety device M5x5mm Torx, 10 pieces"

Genuine FG spare/option part.

Part is delivered in silver or black color from vendor!

Content:

10 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

6933/06 FG Grub screw with Torx M6 x 6 mm, 15 pieces

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

€4.30*

6929/04 FG Grub screw with Torx M4x4 mm, 15 pieces

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

€5.60*

MadMax SUPER GRIP Soft 170x80/x60 for FG, Smartech, HPI, Losi, Arrma & Co.

SUPER GRIP 170 x 80 mm and 170 x 60 mm with black MadMax Extreme rims for 18 mm square or 24 mm hex wheel drive, 20 beadlock screws per rim and reinforced orange beadlock rings. Fits FG, Smartech, Losi 5ive-T, 5ive Mini, Desert Buggy XL and all HPI Baja 5B and 5T/SC cars.Due to the extreme stress created by the MadMax SUPER GRIP tires, the rim has been optimized again.The tires come with a special rigid insert which transfers the applied forces without tilting; even with the heaviest cars like the Losi 5ive-T.All together, the SUPER GRIP lives up to its name and provides maximum grip, which makes it necessary to use the supplied 3 mm beadlock screws for the MadMax EXTREME rims instead of the usual 2.5 mm screws. Additionally, the seating of these screws should be checked after each use.The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video.) On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T and Super Baja Rey should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks!MadMax SUPERGRIP spare rubber can be found here: MadMax SUPER GRIP spare part Some off-road tires knowledge can be found here!

€129.90*

Configure now

7432/23 FG Steel gearwheel hardened 23 teeth - 1pce.

Item N° 7432/23 Steel gearwheel hardened 23 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€30.70*

7432 FG Steel gearwheel hardened 24 teeth - 1pce.

Item N° 7432 Steel gearwheel hardened 24 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€31.90*

67260/05 FG Ball-and-socket joint 7mm for Leopard 2WD/4WD, 4pcs.

Item N° 67260/05 Ball-and-socket joint 7mm, 4pcs.Spare part for the Leopard 2010 2WD/4WD version

€2.90*

Similar products

6745 FG Shim ring 10x16x1mm - 10pcs.

Shim rings to compensate the axial play of the shaft, to use as washers a.s.o.Part is delivered in silver or black color from vendor!

€5.30*

7439 FG Alloy gear carrier 52mm - 1pce.

Item N° 7439 Alloy gear carrier 52mm - 1pce.For 44T - 39T spur gears.For 10 mm diameter shafts.

€41.90*

6730/05 FG Allen Grub screw M5x5 mm, 15 Stück

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

€3.40*

6423 FG Gear protector for 42/44/46/48 T spur gears

Genuine FG spare/option part. Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth. Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.Contents:1 piece

€39.90*

y1426 HT aluminum gear carrier -on-road- with steel spur gear for the layshaft

Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.

€69.90*

Configure now

7439/05 FG Alloy gear carrier 52mm special, 1 pce.

Item N° 7439/05 Alloy gear carrier 52mm special, 1 pce.Precision alloy gear carrier, exact support of the plastic gearwheels 39, 40, 41, 42 and 44 teeth. Very low height design. For 10 mm diameter shafts.Please note: competition layshaft 6041/05 is necessary for installation!

€39.50*

6439 FG Alloy spur gear carrier 60 mm

Genuine FG spare/option part. For 48T - 46T spur gears.Contents:1 piece

€39.50*

7438 FG Alloy gear carrier 47mm - 1 pce.

Suitable for .For 10 mm diameter shafts.

€39.90*

y1427 HT steel spur gear on-road with 39, 40, 41 teeth

y1427 Version: y1427/41 HT steel spur gear

Fits FG and Smartech touring cars in combination with HT aluminum layshaft spur gear carrier on-road y1428. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions

€49.90*

6730/71 FG Allen Grub screw M5x6 mm

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:15 pieces

€3.20*

6495 FG Fine pitch gears EVO 2020

Genuine FG spare/option part. ClutchGear shaft outerGear shaft innerDifferentialReduction ratio345823735,41345823745,49345824735,19345824745,26355823735,26355823745,33355824735,04355824745,11365823735,11365823745,18365824734,90365824744,97375823734,98375823745,04375824734,77375824744,84Contents:1 set

€279.95*

y1379 Pinion fastening set with nut for Losi 5ive-T/2.0 and Mini

This set allows for fastening the pinion to the clutch bell utilizing a full metal self locking nut when using our gas-nitrided clutch bell y0726. The screw will be fully inserted into the clutch bell from the backside using high strength thread locking compound. This setup provides a couple of significant advantages:This self locking nut does not use the usual plastic insert; therefore it is completely temperature resistant!Theres no need to wait for the thread locking compound to cure after a pinion change; the connection is safe and ready to use immediately. For safety reasons nut and spring lock washers should only be used once.No need to worry about worn-out Allen screw heads.In case the screw ever breaks at the point where it enters the pinion, it can still be removed with ordinary tools. Theres still the like new screw head inside the clutch bell ready for screw removal. Set includes:2 pieces of high strength 12.9 grade screws10 pieces of full metal self locking nuts10 pieces of spring lock washers

€5.90*