Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6425/01 FG Stabilizer front/rear for 1/6 scale models

Product information "6425/01 FG Stabilizer front/rear for 1/6 scale models"

Genuine FG spare/option part.

Fits for all 1:6 scale models except Monster-Truck, Monster Beetle Pro and Stadium-Truck. Not suitable for all 4WD cars.

Dimensions:
  • Front: 3 mm
  • Rear: 4 mm


Contents:
  • 1 set

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

Average rating of 0 out of 5 stars

6041 FG Steel layshaft 10 mm
Genuine FG spare/option part. For all FG models except Formula 1.Dimensions:Length: 103 mmDiameter: 10 mmImportant:When installed in a Carson / Smartech model the brake hub is fastened with a screw stomach.Content:1 piece

€21.90*

Average rating of 0 out of 5 stars

6126 FG Brake linkage, complete for Marder
Genuine FG spare/option part. Dimensions:Wire diameter: 2 mmLength: 340 mmContents:1 piece

€9.95*

Average rating of 0 out of 5 stars

6125 FG Throttle linkage, complete for Marder
Genuine FG spare/option part.Contents:1 set

€11.90*

Average rating of 0 out of 5 stars

7050 FG Plastic gear carrier 52mm - 1pce.
For 44T - 39T spur gears.Also available in alloy:

€13.90*

Average rating of 0 out of 5 stars

6534/02 FG Throttle pivot post
Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.

€7.90*

Similar products

Average rating of 0 out of 5 stars

6431 FG Steel pinion 16 teeth
Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece

€26.90*

Average rating of 0 out of 5 stars

6427 FG Plastic gear wheel 46 teeth - 1pce.
46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Average rating of 0 out of 5 stars

6432 FG Steel pinion 18 teeth - 1pce.
Item N° 6432 Steel pinion 18 teeth - 1pce.For combination with 46T main spur gear.Diameter 29,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€33.90*

Average rating of 0 out of 5 stars

6429/01 FG Upright front for 1:6 2WD models
Genuine FG spare/option part.Reinforced version with steel inlay to prevent the M5 bolts from being pulled out.Bearing seats: 22 x 7 mm.Contents:2 pieces

€39.90*

Average rating of 0 out of 5 stars

6431/01 FG Steel pinion 16 teeth, wide - 1pce.
Item N° 6431/01 Steel pinion 16 teeth, wide - 1pce.For use on the clutch bell of FG monster cars.Diameter 26.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€33.90*

Average rating of 0 out of 5 stars

6456 FG Airfilter adapter with choke for Zenoah
Genuine FG spare/option part. As spare parts for engines that have no built-in choke.Fits Zenoah G230/G240/G270RC/G290/ZG22.Content:1 piece

€23.95*

Average rating of 0 out of 5 stars

6451/03 FG Air filter adapter for Zenoah and CY, 1 pce.
Item N° 6451/03 Air filter adapter for Zenoah and CY, 1pce.These air filter adapters are needed fpr mounting the FG air and inlet silencers 6464, 6465 and the K+N air filters 6442 and 6460 as well as 9462 and 6466 on Solo, Zenoah and Tech engines.Fits: Zenoah G230/G240/G260/G270/G290 and CY 23/26 cm³ engines.

€16.90*

Average rating of 0 out of 5 stars

6437/05 FG Tire insert for slicks 63 mm 1:6
Genuine FG spare/option part.Fits for the 1/6 scale front tires. Dimensions:Width: 55 mmHeight: 13 mmLength: 385 mmContents:2 pieces

€13.90*

Average rating of 0 out of 5 stars

6438/05 FG Tire insert for slicks 80 mm 1/6
Genuine FG spare/option part.Fits for 1/6 scale slick tires. Dimensions:Length: 380 mmWidth: 73 mmHeight: 13 mmContents:2 pieces

€14.90*

Average rating of 0 out of 5 stars

6445 FG Spring tension adjustment clips
Genuine FG spare/option part. Required for preload adjustment on FG off-road shocks.For shocks with 20 mm body diameter. Content:6 rings 5 mm wide2 rings 10 mm wide

€8.90*

Average rating of 0 out of 5 stars

6432/01 FG Steel pinion 18 teeth 2-speed - 1pce.
Item N° 6432/01 Steel pinion 18 teeth 2-speed - 1pce.For combination with 46T main spur gear on 2-speed spur gear only.Diameter 29.7 mmBore 10 mmTotal width 16 mmTooth width 9.5 mmModule: m=1,5

€33.90*

Average rating of 0 out of 5 stars

6439 FG Alloy spur gear carrier 60 mm
Genuine FG spare/option part. For 48T - 46T spur gears.Contents:1 piece

€39.50*

Customers also viewed

Average rating of 0 out of 5 stars

67560 FG Stabilizer 4mm, 178mm long, set
Item N° 67560Stabilizer 4mm, 178mm long, setSpare part for Sportsline Leopard.

€17.90*

Average rating of 0 out of 5 stars

7339/08 FG Screw for Carburetor for CY / Zenoah / Fuelie
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Dimensions:M5 x 60 mmContents:2 pieces

€3.70*

Average rating of 0 out of 5 stars

5020/01 FG Front bumper Porsche GT2/GT3
Genuine spare/option part.Suitable for FG Porsche GT2/GT3 body.Dimensions:Length: 340 mmWidth: 115 mmContents:1 piece

€34.95*

Average rating of 0 out of 5 stars

8513 FG Stabilizer 4mm for 2-damper front axle
Genuine FG spare/option part.4mm stabilizer for the 2-damper front axle, not adjustable. Not suitable for Ecoline, Mono-Shock front axle and monster models with four shocks per axle.Contents:1 piece

€19.90*

Average rating of 0 out of 5 stars

10042 FG Wishbone mount
Genuine FG spare/option part.Fits formula 1 cars only.Contents:4 pieces

€12.00*
%

Average rating of 0 out of 5 stars

FG Challenge Line 510 Mini Cooper with 26 cm³ FG engine RTR
With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 510 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required. Incl. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 870 mmWidth: 392 mmHeight: 260 mmWheelbase: 510 mm

From €1,049.00* €1,189.90* (11.84% saved)

Average rating of 0 out of 5 stars

66250/01, FG Bracket f. stabilizer bar front 2WD/4WD, 2 pcs.
For older 2WD models that are not based on the 4WD models, please refer to Sportsline 2008. or if an RC plate is no longer fitted, check Sportsline 13 in Parts Scout.There you will find the right spare parts for your vehicle.

€3.50*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Agency