Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6290/01 FG 3-chamber Tuning pipe Plug-System for Leopard - 1pce.

Product information "6290/01 FG 3-chamber Tuning pipe Plug-System for Leopard - 1pce."

FG 3-unit tuning pipe with Homologation number for FG Leopard Race. According ti the 3-unit technology the noise is limited compared to the standard version. Silencer and manifold aren't screwed but simply plugged in, sealid with o-rings and held with tension springs.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

6350/01 FG Rubber gaskets.
Genuine FG spare/option part.Suitable for FG 6350.Contents:2 pieces

€4.70*

Average rating of 0 out of 5 stars

6350 FG Fuel tube - 1pce.
Fits Zenoah Tank 7348ID 3 mm x L 470 mm

€9.70*

Average rating of 0 out of 5 stars

6402/01 FG Exhaust hose
Genuine FG spare/option part. Heavy gauge teflon tube for connection between exhaust manifold and tuned pipe with da inside diameter from 21 mm and a length from 50 mm.You may have to heat the tube with a cigarette lighter for installation.Contents:1 piece

Content: 5 Zentimeter (€244.00* / 100 Zentimeter)

€12.20*

Average rating of 0 out of 5 stars

6349 FG In-tank fuel filter, 1 pce.
Clunk felt filter, protects the carb against debris in the fuel.

€13.10*

Average rating of 0 out of 5 stars

6268 FG Battery holder - 1pce.

€13.90*

Average rating of 0 out of 5 stars

6403 FG Spring band clamps 24 mm
Genuine FG spare/option part. Recommended accessory for installation of tuned pipes using teflon tube connectors. Contrary to standard hose clamps this version is self-readjusting down until 20 mm inner diameter!Width 12 mm.Content:2 pieces

€6.90*

Average rating of 0 out of 5 stars

6407/05 FG Mini pin M / OR tires, glued, white, 2 pcs.
Item N° 06407/05 Mini pin M / OR tires, glued, white, 2 pcs.Spare part for the Leopard 2010 2WD/4WD versionThe new FG Mini Pin tires are designed for harder grounds. They grant the model a lot of stability and tremendous grip in curves. 153 mm diameter64 mm wideThe version M is suitable for cooler temperatures lower than 20°, die version H is for temperatures over 20°. The tires are glued ready to run on the widened 1:6 wheels.These wheels are suitable for the FG Marder, Beetle, Off-Road Buggy and the monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.

€59.95*

Average rating of 0 out of 5 stars

6299/04 FG Fabric tube Ø24 x 23 f. 06299, 1pce.
Item N° 06299/04 Fabric tube Ø24 x 23 f. 06299, 1pce.Spare part for:

€9.50*

Average rating of 0 out of 5 stars

6423 FG Gear protector for 42/44/46/48 T spur gears
Genuine FG spare/option part. Gearwheel protection in transparent polycarbonate for all 1:6 Off-Road, Monster-Beetle, Big-Foot and Truck models with the gearwheels 43, 44, 46, 48 teeth. Protects the driving gearwheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks and Off-Road ground. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.Contents:1 piece

€39.90*

Average rating of 0 out of 5 stars

6422/01 FG Plastic gearwheel 44 teeth 2-speed - 1pce.
44 teeth plastic main gear for the layshaft with 2-speed gear.Diameter 69 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Average rating of 0 out of 5 stars

6267 FG Battery holder - set
Battery holder and pedestals for installation on chassis plates.BracketLength 157 mmWidth 24 mmDistance between mounting holes 140 mmPedestalsDiameter 8 mmHeight until top of platform 65 mmTotal height 75 mm

€19.90*

Average rating of 0 out of 5 stars

6299/05 FG Extension spring f. 06299/01, 3pcs.
Item N° 06299/05 Extension spring f. 06299/01, 3pcs.

€13.90*

Customers also viewed

Average rating of 0 out of 5 stars

6858 FG Tank bottle 500 ml
Genuine FG spare/option part. Plastic tank bottle, fuel resistant, with angled alloy filler tube, volume 500 ml. For a faster refueling of the models.Contents:1 piece

€15.30*
%

Average rating of 0 out of 5 stars

Original Zenoah engine to choose with carburetor and spark plug
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

€259.90* €299.90* (13.34% saved)
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency