6104/01 FG Front axle shaft, 57 mm
€10.40
% Regular price: €11.90 (12.61% saved)
Available
Product information "6104/01 FG Front axle shaft, 57 mm"
Diameter 8 mm.
Contents:
- 1 piece
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Accessories / Spare parts
Genuine FG spare/option part. Fits FG + Carson 6 mm a-arm hinge pins and 8 mm front wheel shafts.Part is delivered in silver or black color from vendor!Content:15 pieces
Alternatives
Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece
Genuine HT spare/option part. With flat section for the wheel drive set screws.Dimensions:Diameter: 8 mmTotal length: 56 mmLength up to the groove: 54 mmThread length: 10 mmThread size: M6Contents:2 pieces
Customers also bought
The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece
Item N° 32776 Front axle shaft, 65 mm, 2pcs.Dimensions:Length: 65 mmThread length: approx. 12 mmLength from thread to clip: approx. 51 mmDiameter: 8 mm
Fits on Carson models. Not for Gas Devil.
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Customers also viewed
Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece
Genuine FG spare/option part. Suitable for all FG models. Only useable with 9,5mm square driver.Diameter 8 mm.Contents:1 piece
Genuine FG spare/option part. Dimensions:Length: 65 mmThread length: approx. 12 mmLength from thread to clip: approx. 47 mmSpace between clips: approx. 4 mmDiameter: 8 mmContents:1 piece
Item N° 08610/01 Front axle with collar, 1pce.Suitable for all FG front uprights. Suitable for square wheel driver 9,5mm and 14mm. Dimensions: Shaft: 8 mm Outside thread: M6 Inside thread: M4 Total length: 58 mm
Genuine Mielke spare/option part. Contents:4 pieces
Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Contents:10 pieces
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece