Genuine HT spare/option part. Fits all CY / Zenoah engines. Laser cutted stainless steel.The long design increases stiffness of the carburetor assembly significantly compared to the previous version. Comes with gasket and mounting bolt.Content:1 piece
Different versions to choose:y0723 Gas-nitrited tuning clutch bell for FG, Smartech / Carson, Harm, RS5 & Co..Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.y0726 Gas-nitrited tuning clutch bell for Losi 5ive-TGas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.y0726/01 Gas-nitrited tuning clutch bell for Losi DBXLGas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.y0729 Gas-nitrited tuning clutch bell for HPI Baja models, 1 pce.Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
Dust-proof shaft sealing rings to seal the crank shaft of Zenoah and Chung Yang engines. The assembly of these sealing rings is necessary for the use in extremely dusty terrain. Soft material and improved sealing lips prevent an entry of dust and sand in the crankcase which can result in a total damage of the engine.
The Wheelbase of the WB535 2WD version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ Zenoah engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models.The body shell comes unpainted, a decal set with writings for further decoration is enclosed in the delivery.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURAlloy spur gear carrierUse for 48T - 46 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 15The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 217,30 EURThe pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).