4481 FG Carbon fiber rear reinforcement plate

€96.50*

Available

Product number: fg_4481

EAN: 3410569680921

Product information "4481 FG Carbon fiber rear reinforcement plate"

Genuine FG spare/option part.

By mounting the carbon fiber reinforcement deformation of the rear plastic damper plate can be minimized. Recommended at higher ambient temperatures.

Suitable for all FG models except Evo and Formel 1.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Accessories / Spare parts

y19049/01 Upper shock quick mount SW8

Genuine HT spare/option part. The upper shock quick mount makes it easier to change the shocks. No tool is needed, since a small body clip replaces the previously used nylock nut SW8.Fits front and rear axle. Including bolts and body clips.Contents:2 pieces

€10.20*

Customers also bought

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

Similar products

4493/03 FG O-ring for servo saver

Genuine FG spare/option part. Spare part for 4493 and 4494. Thick: 3 mm.Contents:4 pieces

€3.70*

4478 FG Alloy riser plates for rear axle

Genuine FG spare/option part. The complete rear axle assembly is bolted to the solid alloy riser plates. You can now install this unit with only 4 countersunk screws to the chassis, which makes for a very fast change of the complete end.Replacement for plastic base plate FG 7068.Height 9 mmContent:2 pieces

€44.95*

5014 FG RC-plate for 1:5/Truck/Leopard

Genuine FG spare/option part. Plastic radio plate for installation of up to 4 servos. Fits all FG street models (except Formula 1) and Leopard models.You will need FG #6118/05 for installation of any steering servo other than Hitec 805BB.Contents:1 piece

€19.90*

4493 FG Alloy servo saver 04 complete

Genuine FG spare/option part.This servo saver is an improvement of the 04 version. The servo saver part A is now equipped with a flanged sleeve which prevents the servo saver spring from rubbing against the servo saver shaft.Suitable for all FG models.Contents:1 set

€65.50*

4494/03 FG Ball bearing 7x14x5 mm

Genuine FG spare/option part. Contents:2 pieces

€4.60*

4483 FG CFK-body mount front, adjustable

Genuine FG spare/option part. Suitable for all FG touring cars and GT models. Not for Mercedes C291 and Porsche GT1.Contents:1 set

€45.90*

5013 FG Roll cage support left/right

Genuine FG spare/option part. A = 83 mm.Contents:2 pieces

€13.50*

4531/07 FG Titanium wishbone turnbuckle left/right M7x73mm - 2pcs.

Corrosion resistant and 40 % less weight compared to steel.

€45.90*

4492/01 FG Spacer bushing 4x8x15 mm

Genuine FG spare/option part. Spare part for4492.Contents:2 pieces

€5.40*

5010/02 Chassis for FG Sportsline 2WD-465 elektric Porsche GT2

1 pieces

€149.00*

4495/03 FG Servo-saver A

Genuine FG spare/option part. Content:1 piece

€57.10*

4483/01 FG Alloy-body mount front, adjustable

Genuine FG spare/option part. Suitable for all FG touring cars and GT models. Not for Mercedes C291 and Porsche GT1.Contents:1 set

€37.90*

Customers also viewed

66225 FG Alloy a-arm, rear upper 4WD

Genuine FG spare/option part.Contents:1 piece

€25.90*

5010/02 Chassis for FG Sportsline 2WD-465 elektric Porsche GT2

1 pieces

€149.00*

68500, FG 4WD conversion kit for 2WD monster / stadium cars, set

Fits FG Monster and Stadium carsAre you owner of a Monster Truck or Monster Jeep, or perhaps of a Stadium Hummer? You are not really satisfied with the driving performance of your model, or you just want more driving fun? In this case we recommend to install the new 4WD conversion kit made by FG. The conversion kit includes all parts necessary to convert your 2WD Monster model to a 4WD model (complete front diff included). Assembly instructions are included.Fits the following FG cars:- Monster Truck- Monster Hummer- Monster Jeep- Monster Beetle Pro- Stadium Truck-Stadium Hummer- Stadium Jeep- Stadium Beetle ProPlease note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate y0532 separately.The exploded view shows a partially assemled kit, therefore you can't see every single part included! The video shows the FG Off-Road Buggy 4WD during a test drive for a presentation in the Cars & Details magazine!The entire chassis is 100% identical to the FG cars Marder 4WD; Beetle 4WD and Monster / Stadium 4WDEnjoy the video!

€399.95*

6038 FG Engine mount washers for M4 and M4 screws

Genuine FG spare/option part. Washers for the screws (M4 / M5) that hold the engine mounts to the chassis. Suitable for all FG models.Dimensions:Outside diameter: 15 mmInside diameter: 6 mmContents:4 pieces

€6.50*

6432/01 FG Steel pinion 18 teeth 2-speed - 1pce.

Item N° 6432/01 Steel pinion 18 teeth 2-speed - 1pce.For combination with 46T main spur gear on 2-speed spur gear only.Diameter 29.7 mmBore 10 mmTotal width 16 mmTooth width 9.5 mmModule: m=1,5

€33.90*