32549 Shock piston rod
€12.49
% Regular price: €24.99 (50% saved)
Available
Product information "32549 Shock piston rod"
Measures:
- Length: 55 mm
- Diameter: 4 mm
- Thread length: 11 mm
- Distance between slots: 2,9 mm
Content:
- 4 pieces
Login
Customers also bought
Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm
Genuine Smartech spare/option part.Spare part fit for Carson Attack , Super Attack, Attack Evo, Comanche, Gas Devil, CPT, CRT, C5 chassis and other models.Content:4 pieces
Genuine FG spare/option part. Rigid plastic rear plate. Fits all FG 2WD cars except Evo/Competition and Formula 1.Content:1 Piece
Genuine Speed-Tec spare/option part. AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece
Customers also viewed
Carson C5 OEM shocksC5 oil pressure shocks, factory filled, complete with springs, metal body, shaft end and upper mounting tab made of plastic.Dimensions:Lower mounting hole diameter: 4 mmUpper mounting hole diameter: 5 mmTotal length: approx. 135 mmMounting hole distance: approx. 120 mmTravel: 30 mmDiameter: 16 mm
Genuine HT spare/option part. Extra wide tire mounted and glued on genuine 1/6 scale FG Stadium Truck rims 6232/01.Diameter 165 mm, width 90 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.Available in three different compounds:SoftHardWe have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels, which is a labor intensive job. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.However, the original FG-rim lasts without problems!Unit prices:Mammoth tires extra wide: 47,20 EUR / pairMammoth inserts extra wide: 9,70 EUR/ pairGenuine FG wide track rims 6232/01: 29,90 EUR / pairMounting + glueing rims / inserts / tires: 13,00 EURTotal: 99,80 EUR Contents:2 piecesAlso suitable for:With the following wheel adapter: y1183 Rim adapter
The original item 32555 is no longer available. Alternatively, you can use item FG 7088.
Spare part for , , , , , , , , , and .For race actions and also when using high viscous oils we recommend to mount the piston rods with fastening thread for the piston. Through tightening the piston a backlash-free connection with the piston rod is guaranteed. Mount the threaded piston rods only in connection with the alloy damper pistons.Length 55 mmDiameter 4 mmThread length 11 mmDistance between grooves 3.1 mm