10009 FG Formula 1 Competition 1/5 "New Version2025"

Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!

Special offer price!  Including Mecatech Expert hydraulic brake on the front axle.  Vehicle is pre-assembled, with a 26 cm³ combustion engine and almost 100 km/h fast, what more could you want? Another improvement is the hydraulic disc brake in the front wheels.A crystal-clear polycarbonate body is included. Quality and high-quality equipment at a reasonable price. Technical description of the Formula 1 Sportsline chassis: The chassis of the FG Formula 1 is built on a high-strength 5 mm aluminium chassis. All chassis holes (screws) are countersunk from below. The front and rear axle with versatile adjustment options such as camber, caster etc. consists of double triangular wishbones. The double triangular wishbones of the rear axle are supported by additional track rods, with which the adjustment work can be carried out as quickly as possible. Thanks to the mounted wishbone threaded rods with right-hand and left-hand threads, all adjustment work can be carried out without dismantling any parts. The model is equipped with 4 aluminium oil pressure shock absorbers. The push-rod suspension ensures play-free transmission from the individual wheel suspension to the shock absorber. The Formula 1 chassis is supplied with a powerful 26 cm³ combustion engine. Power is transmitted via a four-jaw Teflon clutch to a toothed belt drive. This toothed belt drive is also designed for increased drive power. The BBS rims and tyres were modelled on the large prototypes. All rotating parts are mounted on ball bearings. The construction of the Formula 1 chassis is not identical to the other 1:5 FG models such as the Mercedes C-Class, racing truck etc. and therefore cannot be converted to these models using conversion kits.In unserer Shopauswahl ist das Modell auch inklusive kompletter RTR-Ausstattung erhältlich!RTR AusstattungRTR = Ready to Run. Die RTR-Version wird fahrfertig und mit montierter 2,4 GHz Fernsteuerung ausgeliefert.Sender 2,4 GHzEmpfängerHochleistungsservo für Gas und BremseGroßmodellservo für LenkungSenderakku, EmpfängerakkuMaße:Länge: 960 mmBreite: 440 mmHöhe: 230 mmRadstand: 620 mmFormel 1 Modelle in Action!Antrieb:2WDMaßstab:1:5Motorisierung:BenzinRTR:RTR auswählbar

Special offer price !  Including Mecatech Expert hydraulic brake on the front axle. Highlights News 2025Tuning aluminium lower wishbones, one-piece (front and rear) Tuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibreHighlights Formel 1 Competition- Numerous aluminium parts such as front and rear bearings, damper linkage, engine mount, wishbone ends. - Uniball steel ball joints, which allow all possible adjustments of the front and rear axle- gear drive, which ensures high reliability and optimum function. Like all FG Competition models, the Formula Competition from FG is the most successful model of recent years. The experience gained from the competitions has been incorporated into the latest version. With FG gear drive, which is extremely smooth-running and provides more power reserves. With this version, FG Modellsport has certainly created a competition-ready model for the years to come that will seamlessly build on past successes. Highlights Aluminium wishbones FG Gear drive Aluminium rear axle plate FG Adjustable aluminium shock absorbers Aluminium servo saver with ball bearings 26 cc Zenoah engine Airbox Resonance pipe system Mecha. rear disc brakes 5 mm aluminium chassis  blackLexan bodyworkAnother improvement is the hydraulic disc brake in the front wheels. The chassis of the FG Formula 1 Competition is built on a 5mm aluminium chassis and all screws at the bottom of the chassis are countersunk. The front and rear axle carriers as well as the engine unit are connected to each other over the entire length of the chassis, so that almost the rigidity of a monocoque chassis is achieved. The engine is fixed in place using a quick-release fastener, making it possible to change the engine quickly. The rear axle is driven by several smooth-running spur gears and an FG ball drive on the rear axle. The clutch bell is held by a separate flange bearing to reduce the load on the crankshaft. The front and rear axle with versatile adjustment options such as camber, caster, etc. consists of aluminium wishbones at the bottom. Sturdy aluminium rear axle plates reduce wear on the rear axle and provide enormous driving stability. Four oil-pressure shock absorbers, which are actuated via a push-rod suspension, and stabilisers ensure optimum ground contact.The model is powered by a powerful 26 cc engine with airbox and resonance silencer.The chassis is supplied with tuning bowden cable brakes for the rear axles.Equipment of the FG Formula 1 Competition kit 5 mm aluminium chassis, 26 cm³ engine, intake noise filter, tuning resonance silencer, FG gear drive, ball drive, complete rear axle and front axle carrier unit with integrated quick engine mounting, double aluminium wishbone mountings, aluminium triangular wishbones at the bottom of the rear axle and front axle, front and rear aluminium steering knuckles, ball bearing servo saver, steering stops, pushrods, 4 oil pressure shock absorbers with aluminium shock absorber pistons or mechanical tuning brakes at the front and rear. Servo saver, steering stops, pushrods, 4 oil pressure shock absorbers with aluminium shock absorber pistons or mechanical tuning brakes front and rear, anti-roll bar for front and rear axle, 10 mm aluminium balls, polycarbonate body, polyamide front spoiler, receiver box, competition tyres with tyre inserts.  The models are supplied as a kit with assembly instructions. The body parts are made of crystal-clear polycarbonate for self-painting. These parts are not included and must be ordered or delivered separately if installation is required!To complete the models, you will also need: -  1 remote control system (transmitter, receiver) -  1 large servo for the steering (approx. 40 - 50 kg)-  2 servos for throttle/brake (approx. 20 - 30 kg)-  batteries and charger. IncludetZenoah 26cc engineClear bodyshell and polycarbonate spoilerMechanical brakes rearHydr. brakes frontDimensionsLength: 960mmWidth: 440mmHeight: 230mmWheelbase: 620mmFormular 1 models in action!Drive:2WDMotorization:GasRTR:Without RTRScale:1/5

Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!

Special offer price !  Including Mecatech Expert hydraulic brake on the front axle. Highlights News 2025Tuning aluminium lower wishbones, one-piece (front and rear) Tuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibreHighlights Formel 1 Competition- Numerous aluminium parts such as front and rear bearings, damper linkage, engine mount, wishbone ends. - Uniball steel ball joints, which allow all possible adjustments of the front and rear axle- gear drive, which ensures high reliability and optimum function. Like all FG Competition models, the Formula Competition from FG is the most successful model of recent years. The experience gained from the competitions has been incorporated into the latest version. With FG gear drive, which is extremely smooth-running and provides more power reserves. With this version, FG Modellsport has certainly created a competition-ready model for the years to come that will seamlessly build on past successes. Highlights Aluminium wishbones FG Gear drive Aluminium rear axle plate FG Adjustable aluminium shock absorbers Aluminium servo saver with ball bearings 26 cc Zenoah engine Airbox Resonance pipe system Mecha. rear disc brakes 5 mm aluminium chassis  blackLexan bodyworkAnother improvement is the hydraulic disc brake in the front wheels. The chassis of the FG Formula 1 Competition is built on a 5mm aluminium chassis and all screws at the bottom of the chassis are countersunk. The front and rear axle carriers as well as the engine unit are connected to each other over the entire length of the chassis, so that almost the rigidity of a monocoque chassis is achieved. The engine is fixed in place using a quick-release fastener, making it possible to change the engine quickly. The rear axle is driven by several smooth-running spur gears and an FG ball drive on the rear axle. The clutch bell is held by a separate flange bearing to reduce the load on the crankshaft. The front and rear axle with versatile adjustment options such as camber, caster, etc. consists of aluminium wishbones at the bottom. Sturdy aluminium rear axle plates reduce wear on the rear axle and provide enormous driving stability. Four oil-pressure shock absorbers, which are actuated via a push-rod suspension, and stabilisers ensure optimum ground contact.The model is powered by a powerful 26 cc engine with airbox and resonance silencer.The chassis is supplied with tuning bowden cable brakes for the rear axles.Equipment of the FG Formula 1 Competition kit 5 mm aluminium chassis, 26 cm³ engine, intake noise filter, tuning resonance silencer, FG gear drive, ball drive, complete rear axle and front axle carrier unit with integrated quick engine mounting, double aluminium wishbone mountings, aluminium triangular wishbones at the bottom of the rear axle and front axle, front and rear aluminium steering knuckles, ball bearing servo saver, steering stops, pushrods, 4 oil pressure shock absorbers with aluminium shock absorber pistons or mechanical tuning brakes at the front and rear. Servo saver, steering stops, pushrods, 4 oil pressure shock absorbers with aluminium shock absorber pistons or mechanical tuning brakes front and rear, anti-roll bar for front and rear axle, 10 mm aluminium balls, polycarbonate body, polyamide front spoiler, receiver box, competition tyres with tyre inserts.  The models are supplied as a kit with assembly instructions. The body parts are made of crystal-clear polycarbonate for self-painting. These parts are not included and must be ordered or delivered separately if installation is required!To complete the models, you will also need: -  1 remote control system (transmitter, receiver) -  1 large servo for the steering (approx. 40 - 50 kg)-  2 servos for throttle/brake (approx. 20 - 30 kg)-  batteries and charger. IncludetZenoah 26cc engineClear bodyshell and polycarbonate spoilerMechanical brakes rearHydr. brakes frontDimensionsLength: 960mmWidth: 440mmHeight: 230mmWheelbase: 620mmFormular 1 models in action!Drive:2WDMotorization:GasRTR:Without RTRScale:1/5

The FG Sportsline Formula 1 electric convinces not only by its appearance, but rather by its technical achievements. The unique details such as push rods, horizontal oil pressure shock absorbers, double wishbone and much more can be found in almost no other model.The chassis is built on a high-strength 5mm aluminum chassis plate and thus offers extreme stability. Countersunk holes in the chassis plate allow the screws to be flush, ensuring a flat surface under the model. Versatile adjustment options on the front and rear axles allow the model to be perfectly adapted to your own needs. Adjustments such as camber, caster, etc. are no problem whatsoever, even for beginners, and are made via the double a-arms, which provide maximum stability at the rear axle by means of additional track rods. Also the adjustable aluminum oil filled shock absorbers convince on full length and offer maximum performance even on a very difficult underground. The above mentioned push-rod suspension enables play-free power transfer from the suspension to the shock absorbers, which is essential for precise driving.The factory-mounted combination of 980KV motor and 160A MAX6 esc provides performance that is second to none. With a 6S 22.2V (4S 14.8V is also possible) LiPo batteries, the motor reaches a final speed of about 25,000 rpm, leaving a comparable combustion engine far behind. The braking is done by the 980KV motor and is very strong. Within a few meters the model comes from top speed to a standstill. Those who have searched in vain for reverse gear with a combustion engine will find it with the electric version. The operation is very easy, if you press the brake lever once, you hit the brakes. If you press the brake lever twice, you shift into reverse. With the help of a programming card (available separately) you can adjust all ESC values according to your needs. This includes setting options for power, brake force, low-voltage protection and much more. Furthermore, the model has the following technical: Features: 160A MAX6 esc, 6S compatible (4S also possible) 980KV brushless motor Waterproof components Adjustable aluminum oil filled shock absorbers Aluminum levers for the shocks Aerodynamic Lexan body shell 5mm thick aluminum chassis plate Mounting compartment for steering servo Mounting compartment for separate brake servo (for mechanical/hydraulic brakes) Cogged belt drive Side battery mounts for optimal weight distribution Custom CNC machined motor mount Unique double a-arms Push rod suspension Treaded F1 tires Tuning ball drive shafts Dimensions: Length: 960 mm BrWidtheite: 440 mm Height: 230 mm Wheelbase: 620 mm Technical data 980KV brushless motor: Max. Voltage: 33V Max. Current: 130A Max. Speed: 30.000RPM Power in watts: 4250W Rotor poles: 4 No-load current: 2.8A Resistance: 0.0128 Length: 82mm Diameter: 55 / 58mm with fins Weight: 880g Shaft diameter: 8mm Free shaft length: 30mm Weight: 880g Technical data Max6 esc: Continuous current: 160A Peak current: 1050A Battery: 3S - 8S LiPo or 9-24 cells NiMH BEC: 6V/7,2V - 3A/6A Abmessungen:70x56x46,5mm Weight: 240g Note: In our online shop you can also find a detailed 360° illustration, where especially the technology of the FG Formula1 electric chassis can be seen.Note battery mounting:When mounting the l/h side LiPo battery, you must always make sure that it does not rub against the drive pulley. For this purpose, a 5 mm thick piece of foam mat or something similar between battery and battery holder is sufficient to ensure an appropriate distance. For driving you still need: 2 drive batteries incl. charger Battery dimensions maximum: Length 143 mm/5,6 Width 48 mm/1,9 Height 40 mm/1,6 Connector EC8 The RTR equipment (remote control and steering servo!) The body shell comes unpainted! In our online store you can use our store configurator (shopping cart selection / options menu) to add the desired parts, as well as the completely painted body. Here at our Ebay offer selectable: RTR equipment (remote control and steering servo) fully assembled! Painted body shell incl. decals Formular 1 models in action!

Competition-OnRoad RC car with the latest technical developments. Unique among the large scale models. New stabilizer bar construction front and rear. Ball stabiliszers or frame stabilizers can be used (accessories). 10 mm thick chassis made of T7075 aluminium with cut-outs for weights (also under the tank) and grooves in the front area. This allows the vehicle to be perfectly adapted to the track or the driver. The engine is now again bolted to the chassis for more stiffness. Optimally designed wishbones on front and rear suspension. Reinforced and with toe-in adjustability, which is performed via aluminum wedges. Front upper wishbone for more adjustment possibilities. All gears with fine pitch.Since 1997, i.e. since the beginning of the 1:5 RC car scene, FG Modellsport has been represented with team drivers worldwide at national and international competitions. With the Competition-EVO series, FG won most world championships and almost all European championships. Content Top suspension with 10 mm T7075 aluminum chassis plate Zenoah G230RC Engine Adjustable Tuning Clutch Air filter / Airbox Tuned pipe system Front and rear hydraulic brakes Differential Large volume shock absorbers, black anodized Wheels and rims

Special offer price!  Including Mecatech Expert hydraulic brake on the front axle.  Vehicle is pre-assembled, with a 26 cm³ combustion engine and almost 100 km/h fast, what more could you want? Another improvement is the hydraulic disc brake in the front wheels.A crystal-clear polycarbonate body is included. Quality and high-quality equipment at a reasonable price. Technical description of the Formula 1 Sportsline chassis: The chassis of the FG Formula 1 is built on a high-strength 5 mm aluminium chassis. All chassis holes (screws) are countersunk from below. The front and rear axle with versatile adjustment options such as camber, caster etc. consists of double triangular wishbones. The double triangular wishbones of the rear axle are supported by additional track rods, with which the adjustment work can be carried out as quickly as possible. Thanks to the mounted wishbone threaded rods with right-hand and left-hand threads, all adjustment work can be carried out without dismantling any parts. The model is equipped with 4 aluminium oil pressure shock absorbers. The push-rod suspension ensures play-free transmission from the individual wheel suspension to the shock absorber. The Formula 1 chassis is supplied with a powerful 26 cm³ combustion engine. Power is transmitted via a four-jaw Teflon clutch to a toothed belt drive. This toothed belt drive is also designed for increased drive power. The BBS rims and tyres were modelled on the large prototypes. All rotating parts are mounted on ball bearings. The construction of the Formula 1 chassis is not identical to the other 1:5 FG models such as the Mercedes C-Class, racing truck etc. and therefore cannot be converted to these models using conversion kits.In unserer Shopauswahl ist das Modell auch inklusive kompletter RTR-Ausstattung erhältlich!RTR AusstattungRTR = Ready to Run. Die RTR-Version wird fahrfertig und mit montierter 2,4 GHz Fernsteuerung ausgeliefert.Sender 2,4 GHzEmpfängerHochleistungsservo für Gas und BremseGroßmodellservo für LenkungSenderakku, EmpfängerakkuMaße:Länge: 960 mmBreite: 440 mmHöhe: 230 mmRadstand: 620 mmFormel 1 Modelle in Action!Antrieb:2WDMaßstab:1:5Motorisierung:BenzinRTR:RTR auswählbar

Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.

The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Basic Kit of the FW01 is especially intended for "switchers" and differs from the chassis kit in terms of the brakes and shock absorbers (included in the chassis kit). Here is a list of the parts that are required for completion:brakes, shocks and springs (Difference to Chassis Kit)DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlStock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us!The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01.Included in the basic kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the engineDoes not include- Brakes, shocks and springs- differential- clutch- body and spoilers- Airbox- Engine and linkage- Electronics- Tires