y1610 SPEED TEC Expert 7-channel Zenoah G320 tuning motor, used
€499.00
% €899.00 (44.49% saved)
Available
Product information "y1610 SPEED TEC Expert 7-channel Zenoah G320 tuning motor, used"
The engine is being sold on behalf of a customer and has only been driven one tank of fuel, because the customer has converted to electric drive.
The original price of the motor is €899.
Product information "y1610 SPEED TEC Expert 7-port Zenoah G320 modified engine"
The SPEED TEC 7-port genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina.
More power and torque through the three additional transfer ports.
SPEED TEC V 7-port version modifications:
Cylinder:
- Cylinder bottom modified for higher compression
- enlarged and flow-optimized transfer ports
- machining of three additional transfer ports raises number of ports from 4 to 7
- intake and exhaust ports optimized and matched
- port timing modified
Crankshaft:
- is adjusted, aligned and balanced
Flywheel and ignition:
- Weight reduced and checked for run-out.
Gaskets:
- Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.
With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.
From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:
- When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-T
- When using an aluminum engine mount a stock length clutch housing is required
Separately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.
For all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.
When installing the air filter you must pay attention to the length of the screws.
For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.
When ordering with a modified clutch housing we will include these screws!
In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.
The installation of a Zenoah G320RC in a Smartech C5 onroad car is possible without modifications. However, due to the engines performance aluminum engine mounts (set # y0189) are mandatory!
The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.
| Compatibility Zenoah / Losi 5ive-T: |
| Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine. However, there is a workaround to maintain Zenoah fan cover. The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!
|
Login
Customers also viewed
SCOPE OF DELIVERY AND CONDITION SEE PHOTOS. THE ITEM IS SOLD ON BEHALF OF THE CUSTOMER. The item is in excellent condition. Scope of delivery and condition see photos. VRC TUNING PIPE LOSI DESERT BUGGY XLThis VRC exhaust fits the lower mentioned models with engines from 23 to 29 cc.VRC, Victory RC, exhausts guarantee a considerable power gain in the whole RPM. In general, the power of a standard engine is increased by more than one horsepower, and the low end torque by more than 1 Newton meter.Each pipe is made from thin sheet metal and welded and assembled entirely by hand. This VRC exhaust has an internal noise reducer and consists of several chambers for maximum performance. The very pleasant Race Sound and its volume can be compared to that of a Tuned scooter.Mounting tip; Slide the rubber hose over the pipe and mount the manifold and spring. Then mount the assembly hand-tight on the cylinder. If you know for sure that it is in the right place on the car, fix the pipe and mount the cable ties. We recomend to use the TPS6403/32 clambs.It often seems that the exhaust does not fit, but this is not the case. In the beginning there was a tight fit between the pipe and manifold, but due vibrations the cylinder that was fixed with 2 bolts, and/or the exhaust started to tear. Since a few years, that fit has been made wider to prevent this. But this does mean that the exhaust can move more, this also benefits the assembly on the car. Due to the strong spring the exhaust pulls in one direction, so it seems that the exhaust does not fit.Suitable for:LOSI DBXLLOSI DBXL K&NNB! VRC exhausts cannot be returned and/or exchanged due the possible rust building after handling/unpacking!
Genuine Top Tuning spare/option part, used !- Factory tested - New price 299,90€, top used for 199,90€ ! - Connection cable has been shortened.Specifications:Max. Amps: 200AMax. Voltage: 8-14SMax. Power: 10.000WKV (RPM/Volt): 620KVResistance: 0,0095Mounting hole depth: 8 mmBolt pattern: 4 x M4 on each 30 mm and 40 mm bolt circleCase diameter: 70 mmCase length: 120 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1730gFeatures:High Quality BearingsRotor-4Pole High Quality MagnetsStator-Super Thin Silicon SteelsSuper Strength 8mm ShaftCNC Aluminium Heatsink ShellCopper Wires Of High Temperature EnduranceContents:1 piece
Genuine Top Tuning spare/option part. Specifications:Max. Amps: 200AMax. Voltage: 8-14SMax. Power: 10.000WKV (RPM/Volt): 620KVResistance: 0,0095Mounting hole depth: 8 mmBolt pattern: 4 x M4 on each 30 mm and 40 mm bolt circleCase diameter: 70 mmCase length: 120 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1730gFeatures:High Quality BearingsRotor-4Pole High Quality MagnetsStator-Super Thin Silicon Steels Super Strength 8mm ShaftCNC Aluminium Heatsink ShellCopper Wires Of High Temperature EnduranceContents:1 piece
Original Losi replacement/tuning part. One bore is incorrect. See marking. See photos for scope of delivery. Contents: 1 set
NEW 2025’ FG Short Cross Elektro 4WD model with RTR. Pro trucks or short course are becoming increasingly popular in the world of motor racing. They are monstrous, powerful cars with long suspension travel that make spectacular group races possible. The ‘Short Cross’ has reliable mechanics that are fitted with stiffeners and protective flaps. The standard version is only equipped with motor and controller. The 4WD drive ensures problem-free propulsion on any terrain. The RTR version is also equipped with a servo and 2.4 GHz transmitter.Our battery recommendation - use 2 3S Li-Po batteries.Technical data: - Motor 1100 KV, 3600 W up to 6S - 160A ESC/controller - 4 mm anodised chassis with side protection - Differential with bevel gears - 4WD drive via belt drive via 2 differentials - Completely mounted on ball bearings - Big Bore aluminium shock absorbers - Front and rear double wishbones adjustable in caster/toe-in/camber - New short course tyres and high-sided rims in M and S hardness. - Matt-black painted and finished bodyFor completion you need : - Batteries, - charger - 1 large steering servo - Transmitter/receiver setDimensions and weight: - Length 770 mm - Width 480 mm - Height 320 mm - Wheelbase 485 mm - Weight approx. 10 kg1 pieces