y1388 Offroad tuning springs Dirt-Spring DBXL/XL-E +MTXL

Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/07 - 3,2 x 110 mm Pinky1388/08 - Complete set, unit prices: 132,93 EUR / Offer price: 89,99 EUR

Genuine Top Tuning spare/option part. Indispensable for optimal suspension tuning!Vacuum container for removal of bubbles from shock fluid when filling shocks.A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled". Tray bore sizes: No. 1 = 32 mm diameter No. 2 = 21 mm diameter No. 3 = 17.5 mm diameter No. 4 = 15 mm diameter The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)Operation:Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort. Content: Can with integrated vacuum pump Shock tray

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 100 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 100 ml:FG Item N° 66295/010 = Viscosity: 100 FG Item N° 66295/025 = Viscosity: 250FG Item N° 66295/035 = Viscosity: 350FG Item N° 66295/050 = Viscosity: 500FG Item N° 66295/075 = Viscosity: 750FG Item N° 66295/100 = Viscosity: 1000FG Item N° 66295/150 = Viscosity: 1500FG Item N° 66295/200 = Viscosity: 2000FG Item N° 66295/300 = Viscosity: 3000FG Item N° 66295/400 = Viscosity: 4000FG Item N° 66295/500 = Viscosity: 5000FG Item N° 66295/600 = Viscosity: 6000FG Item N° 66295/700 = Viscosity: 7000FG Item N° 66295/800 = Viscosity: 8000FG Item N° 66295/900 = Viscosity: 9000FG Item N° 66296 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 50 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 50 ml:FG Item N° 6510/010 = Viscosity: 100FG Item N° 6510/025 = Viscosity: 250FG Item N° 6510/035 = Viscosity: 350FG Item N° 6510/050 = Viscosity: 500FG Item N° 6510/075 = Viscosity: 750FG Item N° 6510/100 = Viscosity: 1000FG Item N° 6510/150 = Viscosity: 1500FG Item N° 6510/200 = Viscosity: 2000FG Item N° 6510/300 = Viscosity: 3000FG Item N° 6510/400 = Viscosity: 4000FG Item N° 6510/500 = Viscosity: 5000FG Item N° 6510/600 = Viscosity: 6000FG Item N° 6510/700 = Viscosity: 7000FG Item N° 6510/800 = Viscosity: 8000FG Item N° 6510/900 = Viscosity: 9000FG Item N° 6511 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Genuine HT spare/option part. Fits Losi 5ive-T und Mini, UFRC Growler GX1, Carson Gas Devil/ Hell Devil 4x4. Not for Thunderbolt!.Dimensions:Socket: approx 33 mmInner diameter: approx 31 mmOuter diameter: 37 mmLength short spring: 103 mmCoils short spring: 8 StückLength long spring: 143 mmCoils long spring: 10 StückFront axle:TypeMeasuresColorItem N°Losi2.3 x 103 mmyellowy0351/01Losi2.4 x 103 mmredy0351/02Losi2.6 x 103 mmbrowny0351/03Losi2.75 x 103 mmbluey0351/04Losi2.8 x 103 mmsilvery0351/05Losi2.9 x 103 mmblacky0351/06Rear axle::TypeMeasuresColorItem N°Losi2.3 x 143 mmyellowy0351/07Losi2.4 x 143 mmredy0351/08Losi2.6 x 143 mmbrowny0351/09Losi2.75 x 143 mmbluey0351/10Losi2.8 x 143 mmsilvery0351/11Losi2.9 x 143 mmblacky0351/12Contents:2 pieces

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC.Increases track width by 25 mm. Fits all versions of DBXL / DBXL-E / 2.0 (brushless and gas) and MTXL. 2 mm O-rings protect against drive pin loss.Set of four including O-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/07 - 3,2 x 110 mm Pinky1388/08 - Complete set, unit prices: 132,93 EUR / Offer price: 89,99 EUR

Genuine silicone shock absorber oil for the optimal shock absorber set-up. Content: 50 ml Please note: Factory filling of FG/Losi/Smartech and many other 1/5 and 1/6 scale shocks is done with genuine silicone shock absorber oil. To ensure seal tightness and consistency you should only use genuine silicone shock absorber oil for refilling as well.Most every rc-car shock absorber uses silicone oil of different viscosities. The smaller the number, the lower the viscosity of the silicone oil and the softer the damping. As a rule of thumb: Viscosity 100 = similar to water Viscosity 1.000 = similar to cooking oil Viscosity 5.000 = similar to shampoo Viscosity 10.000 = similar to honey As a reference: The red FG Marder / Off-Road Buggy series shock absorbers are factory filled with 2.000 viscosity oil, the shocks on monster cars with dual shock set-ups (total of 8 shocks) are filled with 1.000 viscosity oil, and the shocks on FG onroad cars come filled with 4.000 viscosity oil. The original filling of the Losi 5ive-T is 350cc silicone oil.FG Silicone oil with 50 ml:FG Item N° 6510/010 = Viscosity: 100FG Item N° 6510/025 = Viscosity: 250FG Item N° 6510/035 = Viscosity: 350FG Item N° 6510/050 = Viscosity: 500FG Item N° 6510/075 = Viscosity: 750FG Item N° 6510/100 = Viscosity: 1000FG Item N° 6510/150 = Viscosity: 1500FG Item N° 6510/200 = Viscosity: 2000FG Item N° 6510/300 = Viscosity: 3000FG Item N° 6510/400 = Viscosity: 4000FG Item N° 6510/500 = Viscosity: 5000FG Item N° 6510/600 = Viscosity: 6000FG Item N° 6510/700 = Viscosity: 7000FG Item N° 6510/800 = Viscosity: 8000FG Item N° 6510/900 = Viscosity: 9000FG Item N° 6511 = Viscosity: 10000Viscosity of silicone oil at various temperatures.

Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

Set consists of 4 dampers. Premium version, suitable for FG, Carson / Smartech etc. Fully assembled and filled.  Special features: 16 mm inner diameter for higher oil volume Volume equalisation Housing and screw connections made entirely of aluminium Hard anodised housing Precision piston made of Delrin, machined (no moulded part!) Aluminium piston rod base and aluminium spring plate Replaceable bearing bushes in the mounting eyes Pre-filled with 1000 silicone oil. For the following models: FG 4WD: Monster Truck, Monster Jeep, Monster Hummer, Stadium Truck, Stadium Jeep, Stadium Hummer, Off-Road Beetle  Set contents: Four long dampers with 5 mm mount in the upper damper caps. Damper feet one pair short, one pair long (4WD MT version).  We recommend our progressive off-road tuning shock absorber springs from the "Dirt-Spring M" series, part number y0321, for the shock absorbers.  The original springs can also be used on FG models!  Silicone oil recommendation:  The GPM-Spezial Cross shock absorbers are filled with silicone oil viscosity 1000. This viscosity provides very good damping properties at normal outside temperatures.  If softer damping is required, oil with a viscosity of 500 or 600 is recommended; for harder damping, 1500 or higher is recommended.  One 50 ml bottle of y0038 is sufficient for five long or six short dampers.