Genuine HT spare/option part. Universal decals suitable for all body shells. The decals are printed on white film and have to be cut out by yourself.Size (Height x Width):Complete sheet: 300 mm x 410 mmContents:1 piece
Genuine HT spare/option part. Universal decals suitable for all body shells. The decals are printed on white film and have to be cut out by yourself.Size (Height x Width):Complete sheet: 300 mm x 410 mmContents:1 piece
Contains the vehicle specific decals for an original appearance.The set consists of a total of three different decal sheets.For body shell no. y1518 and y1562.Content:1 set
Suitable for the lights on off-road cars like Losi 5ive-T or HPI Baja cars and also for embellishment of other body shells.Dimensions:Diameter: 32 mmContentt:Four teeth orange smiliesFour dead yellow smiliesFour red scullsFour green rc srokes
Item N° 3021Front bumper CAT-Truck - setComplete foam bumper, increased protection for chassis and body shell. The bumper comes cut to size and ready for installation.Suitable for CAT-Truck body shell.Length 86 mmWidth 360 mmHeight 58 mm
Item N° 50353021Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.This is an Alloy Support Block anodized in black colour with 35mm height.The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Genuine Smartech spare/option part.Please note: It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContent:1 piece
Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces
Offerset:1 Pair MadMax Tarmac Buster front tires 170x60 mm1 Pair MadMax Tarmac Buster rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01 TARMAC BUSTER 170x80 and 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced silver headlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars. Due to the extreme load created by the MadMax TARMAC BUSTER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01. The TARMAC BUSTER MadMax are designed for use on flat surfaces. Your car will have good traction even on smooth pavement!We recommend to check the beadlock screws after the run. Dimensions:Outer diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
From
€139.90*
This product is currently not available.
This website uses cookies to ensure the best experience possible. More information...