Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

14 products found for "y1488"

Filter products

rc-car-online - Home

Average rating of 0 out of 5 stars

y1481 RC-Paint Spray Gun
Fits most spray cans from many manufacturers.Convert your spray can into a spray gun. The long-lever system of this handle makes using a spray can much more convenient and provides better flow rate control as well.No more dirty hands from paint work.Contents:1 piece

€9.95*

Average rating of 0 out of 5 stars

y1489 spark plug gap tool
Genuine HT spare/option part.Low height design, allows for easy gap measurement and adjustment without damaging the electrodes.Gauge measures spark plug electrode gaps on gap plugs. Ramp style increments on the outside with a .020-.100 inches range.Use an electrode gap of about .030 for best results.Long lasting solid steel alloy.Contents:1 piece

€4.90*

Average rating of 0 out of 5 stars

y1588 Aluminum receiver antenna mount
Genuine rc-car-online spare/option part. Versatile aluminum bracket for easy installation in panels or RC boxes with up to 4 mm wall thickness. Only a 6 mm hole is required and the bracket is fastened with the included nut. Alternatively, for installation in thicker material an M6 thread can be tapped as well. An O-ring provides a seal when installed in RC boxes.The bracket has a stepped hole into which the common antenna tubes of about 3.2/3.3 mm diameter can be inserted, but not pushed through. The hole for the antenna cable has a diameter of approx. 2.5 mm.The height of the bracket above the mounting surface is 16 mm.The scope of delivery includes an end cap and two antenna tubes with a length of approx. 170 mm.Contents:1 set

€9.90*

Average rating of 0 out of 5 stars

y1486 Threading die M12 x 1,25
Genuine HT spare/option part. Die for removing the remains of microencapsulation on the stock Traxxas X-Maxx wheel shafts.After a few tire changes microencapsulation becomes very hard. This will cause the risk of thread seizure and damage. Timely removal of the residues prevents this. A die holder is not required. Turning the die with bare hands will do the job easily.Contents:1 piece

€12.90*

Average rating of 0 out of 5 stars

y1468 Tray for small parts with magnetic vinyl
Genuine HT spare/option part. Once again misplaced nut or bolt or, or ... . The tray for small parts with magnetic vinyl brings this to an end!Dimensions: Length: 105 mmWidth: 85 mmdepth: 10 mmContent:1 Piece

€9.90*

Average rating of 0 out of 5 stars

y1188 Pin 4 x 18 mm, 10 pcs.
Hardened steel pins to replace lost or worn pins in driveshafts (dog bones) on FG / Carson / Smartech cars.It is recommended to use high strength thread locking compound for the installation.

€3.90*

Average rating of 0 out of 5 stars

y0488 mf-RaceLine Cask shaped springs, green 2,5 mm, 2 pcs.
The famous cask shaped spring by Markus Feldmann. Especially designed for rear suspension applications.Fits all touring car shock absorbers with an outer diameter of 16 mm.Caution: Not suitable for MecaTech Klick shocks.Dimensions:Height: 52 mmCenter diameter (outside): 30 mmInner diameter (top/bottom): 16 mmCable thickness: 2,5 mm

€17.90*

Average rating of 0 out of 5 stars

y1478 pump for re-fueling and de-fueling
The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece

€19.90*

Average rating of 0 out of 5 stars

y1483 Walbro WT-1048 Racing carburetor
y1483 Version: y1483/01 WT-1048 Racing carburetor
Genuine Walbro spare/option part.Popular performance carburetor without choke; with 13.5 mm venturi diameter, especially suitable for large-displacement engines like the Zenoah G320.The stock throttle shaft has been replaced with the proper version required for car applications; including the throttle lever as well.All existing throttle linkages can therefore be connected as usual without modifications.This carburetor does not feature a primer bulb nor a connection for a return line. It is therefore only connected to the supply line from the tank, the return line of the tank has to be closed.Optional ball bearing of the throttle shaft can be selected from the shops menu.Contents:1 piece

€97.90*

Average rating of 0 out of 5 stars

y1388 Offroad tuning springs Dirt-Spring DBXL/XL-E +MTXL
y1388 Version: y1388/02 - 2,6 x 110 mm Blue, 1 pair
Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/07 - 3,2 x 110 mm Pinky1388/08 - Complete set, unit prices: 132,93 EUR / Offer price: 89,99 EUR

€21.99*

Average rating of 0 out of 5 stars

y1438 Front section BMW M3 Superstars, clear
y1438 Thickness: y1438/03 - 2,00 mm version+ 4.55EUR
Spare part for y1437 BMW M3 Superstar body shell.Available material thicknesses:1.0 mm2.0 mmPainting tips:

Variants from €32.95*
€34.21*

Average rating of 0 out of 5 stars

y1418 Heavy duty bead lock rings for MadMax rims
y1418 Color: y1418/02 - Blu
Can be used as reinforcement for genuine HPI and Losi rims as well.Set includes:Two pieces of reinforced outside ringsTwo pieces of reinforced inside ringsand 40 pieces of 2.5 mm allen head screws (for 2 mm allen wrench)Colours:y1418/02 - Bluey1418/03 - Redy1418/05 - Yellow

€17.90*

Average rating of 0 out of 5 stars

y1428 HT aluminum layshaft spur gear carrier “on-road”
y1428 Version: y1428/01 Suitable for FG and Smartech touring cars
Fits FG and Smartech touring cars in combination with HT steel spur gear on-road y1427. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The carrier is available in two versions:y1426/01 Suitable for FG and Smartech touring cars (not for EVO 2020)y1426/02 for FG touring cars EVO 2020

€44.90*

Average rating of 0 out of 5 stars

y1482 Spring band clamps for tuned pipe connectors, 22 to 34 mm diameter range
y1482 Size / piece: y1482/06-5 Spring band clamps 27 - 29 mm+ 4.5EUR
Genuine HT spare/option part.Spring band clamps are self-clamping and can self-adjust to diameter changes due to temperature variations or properties of the tube material.With this feature of self-adjustment, spring band clams are ideally suited for hose connections between exhaust manifold and tuned pipe with their high temperature load.Unlike worm drive clamps with their relatively large adjustment range, spring band clamps must be selected closely related to their intended application. For this purpose, the outer diameter of the hose in the mounted state must be measured. The clamp, whose nominal diameter corresponds most accurately to the value determined, should be used.In the options menu you can select from sizes ranging from 22 to 34 mm and packs of one or five clamps.Contents:1 piece / 5 pieces

Variants from €0.99*
€5.49*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Plugin Development