10 products found for "y1474"

rc-car-online - Home

y1474 Aluminum foil tape, self-adhesive, 50 mm x 45 meters

Genuine HT spare/option part.50 mm wide, self-adhesive aluminum foil tape, especially for heat insulation; i.e. between tuned pipe and plastic or electronic components.Content:1 piece / 45 meters

€9.90*

y1434 VL32 Multi Oil Pen for RC-Car sport

Universal maintenance oil which has a high resistance to environmental influences; it is penetrating and moisture displacing with an excellent corrosion protection. Precise application is possible with the VL32 - Multipen's metal syringe tip. The ergonomic shape and rubberized handle provide a secure grip. Leakage of oil is prevented by the safety valve in the cap. Application: u> b>Pull off cap (avoiding strong pressure on the pen!), position the pen to the point of lubrication and press. Refit cap after use.Content:12 ml / 1 piece

Content: 12 Milliliter (€741.67* / 1000 Milliliter)

€8.90*

y1471 Turnbuckle wrench 6 mm

Genuine HT spare/option part. Handy wrench for 6 mm turnbuckles.Maße: Wrench size: 6 mmLength: 75 mmContent:1 piece

€9.90*

y1470 Antenna tubes with caps, set of 5

Genuine HT spare/option part. Five antenna tubes with caps.Size: Length: 300 mmContent:1 set

€7.90*

y1444 Mounting bracket for tuned pipe mufflers

Genuine HT spare/option part. Extra large bracket with wide surface allows for the use of two strong cable ties at the same time. You can even use a hose clamp at ones own discretion. The bracket comes with M5 lens flange head screw, nut and washer as well as with special temperature resistant cable ties. Content:BracketEach M5 screw, nylock nut and washer4 x temperature resistant cable tie 4,8 x 290 mm

€9.90*

y1475 Special front hinge pin brace set for Losi Mini

Genuine HT spare/option part.These hinge pin braces are machined from 7075 aluminum and feature an increased distance between the holes for the hinge pins. They are to be used in place of stock braces LOSB 078F.This allows the use of the front center drive shaft from the 5ive-T LOSB3218 at the wheels. This one is slightly longer than the Mini shaft for the wheels LOS252000, but will be available as spare part in the future. The turnbuckles on steering rods and camber links need some minor readjusting after assembly to restore the correct geometry.At the rear LOSB3218 driveshafts will fit the Mini without modifications. Set with one each front and rear hinge pin brace.Contents:1 set

€9.90* €24.90* (60.24% saved)

y1473 Extra strong duct tape, 50 mm x 50 meters

Genuine HT spare/option part.50 mm wide, extra strong duct tape, i.e. for repair of cracks in body shells or for preventative taping of RC car body shells.Content:1 piece / 50 meters

€6.90*

y1478 pump for re-fueling and de-fueling

The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece

€19.90*

y1464 MadMax SUPER GRIP 170x80/x60 replacement wheels

The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!

From €29.90*

Details

y1477 Losi 5ive-T/2.0/B and Losi MINI 300m steel HD differential drive cups, booted f/r

y1477 Versin: y1477/02 Set for the rear axle+ 20EUR

Genuine HT spare/option part.These heavy duty differential drive cups for front or rear differential in a Losi 5ive-T/B or MINI WRC are made of 300M / Böhler V132 steel and are characterized not only by high hardness, but also simultaneously toughness. The service life is therefore much higher than for the stock cups.300M steel is used in motorsport and aviation for high strength parts. As a highly pure material, it is significantly more expensive than conventional steels, its high basic strength and toughness make the machining a time-consuming task.The shape of these drive cups now allows the use of driveshaft boots and grease lubrication, which increases service life enormously. In addition, these HD drive cups have two sets of slots for the pin of the drive shaft, this means another doubling of the service life.We recommend y0809 Klüber grease for lubrication of closed HD drive cups.A dry run like with stock parts is theoretically possible, but absolutely not recommended because it would waive the enormous advantage of encapsulated lubrication and the associated wear reduction. The set for the rear includes modified stock alloy bearing carriers, which provide improved clearance for the driveshaft boots.You can find advices for installation at the specifications-tab.Contents:Front set:2 pieces of 300M steel HD differential drive cup, front and rear application2 pieces of driveshaft bootsRear set:2 pieces of 300M steel HD differential drive cup, front and rear application1 pair of modified bearing carriers2 pieces of driveshaft boots

Variants from €119.90*

€139.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

10 products found for "y1474"

Filter products

rc-car-online - Home