9 products found for "y1366"

rc-car-online - Home

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

y1360 MD Two-component glue CA-STAR 2K met

Best adhesion properties on many different materials: many metalls like steel / aluminum / stainless steel, many plastics, rubber, porous / absorbent materials.Mixing ratio: 4:1Processing time: approx. 35 minutes Temperature resistance: -20°C to +80°C, short term up to +120°CFeatures:ThixotropicDrip freeExtremely impact resistantMechanical editableGap fill up to 6 mmApplications overhead and in vertical locationsGood chemical resistanceLow bloomingColor: grey

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

y1361 Speed Tec tuning ignition coil Löhin RS4-332

Genuine Speed Tec spare/option part. Speed TEC Tuning Ignition Löhin RS4 332 new ignition system with offset ignition timing and modified spark breakaway. Advantage of the ignition system: better starting and acceleration due to the modified ignition timing. Higher ignition voltage through modified spark breakaway, resulting in increased charging time for the coil, thereby considerably more torque in the medium rpm range. Suitable for Zenoah and CY engines without modifications. In the picture you can see the original Löhin ignition.Contents:1 piece

€89.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt CY engines

Full set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket

€12.90*

y1366 TURBO-TWIST 325 mm special XXL screw driver

y1366 Version: y1366/01 - Phillips no. 0 / PH0

TURBO-TWIST, 325 mm long screw driver in top quality.Allows easy access to hard-to-reach screws in any 1/5 & 1/6 car.Features:Soft Grip handlesExtra long 325 mm shaftChrome Vanadium hardened and tempered bladesBlackened magnetic tipsVersions:y1366/01 - Phillips No. 0 / PH0y1366/02 - Phillips No. 1 / PH1y1366/03 - Phillips No. 2 / PH2y1366/04 - Flat 1.2 x 8 x 325 mm

€6.90*

y1396 Reed valve piston

y1396 Version: y1396/29 - Zenoah G290

Genuine Zenoah piston with machined recess for use with Are reed valve block BJ035. Please note: Differing widths of the remaining webs of the piston skirt are caused by production spread of the pistons.Version:y1396/29 - Zenoah G290y1396/32 - Zenoah G320Content:1 piece

€39.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1466 Gasket kit for all engines

y1466 Version: y1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt Losi, HPI, CY engines

y0467 Complete gask set for Zenoah 230 + 260, CY, Reely, HPI and Losi 2 bolt engines, setHigh quality gasket set for all G230 and G260 Zenoah engines, all Chung Yang, Reely an HPI Fuely engines from 23 to 30,5 cc. Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Set includes gaskets for:cylinder bottomcarburetorisolatorexhaustcrankcasey1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt Losi, CY enginesFull set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket0.5 mm air filter gaskety1016/112 Complete Zenoah G320 sealing setSet includes:y1016/005 Cylinder gasket G320RCy1016/007 Insulator gasket G320RCy1016/013 Crankcase gasket G320RC7332 Silencer gasket7337 Carburetor gasketUnit prices: 20,10 EURy1386/02 SCZ Sealing set for E290 race engineGenuine SCZ spare/option part.Set includes all necessary seals.

€12.90*

y1362 Zenoah carburetor body for WT 603/668/668A

y1362 Version: y1362/02 - for WT 668

Genuine Zenoah carburetor bodies, direct replacement for the used part.Available versions:y1362/01 - for WT 603y1362/02 - for WT 668y1362/03 - for WT 668A

€34.90*

y1367 TURBO-TWIST 325 mm special carburetor screw driver

y1367 Version: y1367/01 - 1,0 x 5,5 x 325 mm

TURBO-TWIST, 325 mm long screw driver in top quality. Allows you to set the carburetor on almost any 1:5 / 1:6 model also with a mounted body shell.On most models, you have to adjust the motor with this screwdriver does not even stoop.Caution:May differ from picture!

€9.90*

9 products found for "y1366"

Filter products

rc-car-online - Home