43 products found for "y1308"

rc-car-online - Home

y1008 CFH gas

Genuine HT spare/option part. Propan/Butan gas mix for the torch above, similar units and cigarette lighters. Contents:1 piece / 100 ml

€3.50*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

y1303 T-connector charging cable 4mm

Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

y1380 High performance starter rope, carbon grey

3 mm high performance starter rope; with a breaking strength of almost a metric ton it is far superior to any other starter rope available. Even large displacement high compression engines are no match for this rope. Please note:The usual fusion of cutting edges and knots on standard starter ropes using a flame is mostly unrewarding with this rope! We therefore recommend securing the knots with 2 - 3 drops of superglue on the outside. Length approx. 80 cm; fits all current pull starters.

€8.90*

y10308 Flanged bushing (8x12/16x5 mm), aluminum, coated

Replacement part for Power-Lock differential 2014 version with the order number y8605.

€11.90*

y1208 HT Aluminum a-arm for Carson/Smartech Off-Road

Genuine HT spare/option part.Very strong a-arm, allows for camber adjustment. Features Igus bushings for the hinge pins (stock hinge pins can be re-used).Fits Smartech Monster, Carson Comanche, Attack Evo, CRT 2WD and CPT. Contents:1 piece

€39.90*

y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP

Genuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piece

€39.90*

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

y1608 SPEED TEC CRANK Team-Edition Zenoah G320 7-port Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Crankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€1,099.00*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1358 PTFE thread sealing tape, 12 mm wide, 10 m roll

Perfect for sealing threads.Resistant against almost all chemicals.Dimensions:Width: 12 mmThickness: 0.075 mmLength: 10 meters

€2.90*

y1338 Epoxy P-R-M Race brake discs for Losi 5ive-T and Mini

Top quality epoxy P-R-M Race brake discs with four dirt slots and 12 4-mm holes for removing dirt and abrasion, which will be transferred to the outside by the discs rotation. The epoxy R-P-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup!)! With an extremely heavy car like the Losi 5ive-T and Mini exceptionally good braking effect is especially important, of course! The best braking action when using the epoxy RPM Race brake disc is achieved by the combination of the epoxy brake discs and the stock Losi 5ive-T and Mini steel brake pads! The epoxy R-P-M Race brake discs for the Losi 5ive-T/Mini are a direct replacement for the original aluminum brake discs. Dimensions: Outer diameter: 60 mm Thickness: 3 mm socket for the stock Losi 5ive-T/Mini drive cup Weight: 383 grams/ pair

€19.90*

y1308 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and Mini

y1308 Version: y1308/03 Set with mount A and Mount B+ 27.9EUR

Genuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 set

Variants from €44.90*

€72.80*

y3308/T2 Orange Genuine Losi 5ive-T body shell set, 2.0 painted

This genuine factory painted Losi 5ive-T body shell set with decals .New version of the 5ive-T body shell with scoop on the hood for optimized cooling!The set includes the following genuine parts (unit parts only clear available!): LOS350005 Front sectionLOSB8102 Center sectionLOSB8103 l/h rear fender with plateLOSB8104 r/h rear fender with plateLOS259003 Vehicle decalwith factory paint job on all body parts and decals applied. Delivery without roll cage!

€279.90*

y1388 Offroad tuning springs Dirt-Spring DBXL/XL-E +MTXL

y1388 Version: y1388/02 - 2,6 x 110 mm Blue, 1 pair

Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/05 - 2,9 x 110 mm Whitey1388/06 - 3,0 x 110 mm Goldy1388/07 - 3,2 x 110 mm Pinky1388/08 - Complete set, unit prices: 132,93 EUR / Offer price: 89,99 EUR

€21.99*

y1301 T-connector male / female spring loaded 4 mm contact

y1301 Version: y1301/03 male + female+ 1.8EUR

T-connector male / female with spring loaded 4 mm contact.Select from:y1301/01 - male connectory1301/02 - female connectory1301/03 - one each male and female connector

Variants from €1.80*

€3.60*

y1303/04 T male to EC5 female

Adapter cable T male to EC5 female.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

y1303/06 TRX female to T-connector

Genuine HT spare/option part.Adapter TRX female (Traxxas batteries) to T-connector.Adapter cable for the LiPo receiver battery in model Traxxas Xmaxx.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

Details

y1303/10 EC5 connector, female

Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

y1303/11 EC8 male connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected plug with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm sockets found on many larger ESCs.Contents:1 piece

€5.90*

y1303/17 XH Balancer extension cable 2S-4S

y1303_17 Version: y1303/17-S3 XH Balancer extension cable+ 0.5EUR

Genuine HT spare/option part.Extension cable for convenient charging of LiPo batteries with XH connector, since the standard balancer connection on the battery is usually uncomfortably short. Available for 2S, 3S and 4S batteries. Silicone insulated cables with a length of approx. 20 cm.Content:1 piece

Variants from €3.40*

€3.90*

y1303/02 EC3 to female T-connector adapter cable

Adapter cable EC3 male to T-connector femaleDimensions:Length cable: 46 mmTotal length: 72 mmContent:1 piece

€9.90*

y1303/18 T-connector male to HXT4 battery side

Genuine HT spare/option part.Adapter cable T-connector male to HXT4 battery side. Dimensions:Cable length: 50 mmTotal length: 97 mmContent:1 piece

€9.90*

y1303/26 Adapter cable T- connector female to Tamiya female

Genuine HT spare/option part.Length approx. 160 mm, 18 AWGContent:1 piece

€9.90*

y1303/12 EC8 female connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected socket with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm bullet connectors found on many larger brushless motors.Contents:1 piece

€5.90*

43 products found for "y1308"

Filter products

rc-car-online - Home