52 products found for "y1304"

Catalogue #1

y1303 T-connector charging cable 4mm

Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

This product is currently not available.

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP

Genuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piece

€39.90*

y1324 MadMax tyre inserts green 165x65mm, for Maxi Pin tyres

Mittelfeste, geschäumte, grüne Reifeneinlage mit profilierten Kanten und eingeformten Senkungen für die Felgenverschraubung.Die mittlere Shorehärte der grünen Reifeneinlage in Topqualität stützt die Reifenschulter optimal und ermöglicht somit ein perfektes Abrollverhalten des jeweiligen Reifens.Die ideale Einlage für einem Reifendurchmesser von 185mm und 70mm breite.Ersatzteil zu MadMax Reifen Maxi Pin.2 Stück, 1 Paar

€29.90*

y10304 External fins 0.50 mm, perforated

Replacement part for Power-Lock differential 2014 version with the order number y8605.

€21.50*

y1104 Maintenance tray for 1/5 cars

Genuine HT spare/option part. Maintenance tray for all 1/5 scale RC car models. The tray with its rubber pad prevents the car from sliding while working on the vehicle at the race or in the basement.Dimensions:Length: 370 mmHeight: 60 mmWidth: 170 mmContents:1 piece

€44.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1604 SPEED TEC CRANK Team-Edition Zenoah G290 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Piston:Transfer port area optimized for flow and polished, weight reducedand the piston-roof is polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

y1034 HT Aluminum front suspension for FG Off-Road Buggy 2WD, set

The sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1035HT Aluminum shock tower Off-Road Buggy 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 387,10 EURFits FG Off-Road Buggy 2WD.This front suspension can be used on a FG Monster Beetl 2WD as well, however some new holes must be drilled into the shock tower for this application.

€339.00* €387.10* (12.43% saved)

y1344 GPM Air filter cover for Losi Desert Buggy XL/2.0

GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.

€13.30*

y1340 Adjustable wing mount with wing for Losi Desert Buggy XL, DBXL-K&N

Wing mount set for the Losi Desert Buggy XL. Due to the exposed position of the rear wing on the Losi Desert Buggy and the vehicle weight this mount is designed to be extremely tough!Your choose of decal sheet with DBXL and K&N design included. The mount installs to the roll cage at four points without drilling. The wings tilt angle is adjustable to four different settings from 0° to 27°. The set includes:Ten pieces aluminum wing mount Mounting screwsOne Offroad Flex-Wing # y1099One Losi Desert Buggy wing decal

€79.90*

y1303/10 EC5 connector, female

Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

y1303/11 EC8 male connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected plug with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm sockets found on many larger ESCs.Contents:1 piece

€5.90*

y1204 HT Aluminum front suspension for Carson Comanche, Attack Evo, CRT 2WD + CPT, Smartech MT, Pick-up Truck, Cross Beetle, Monster Beetle

The set includes:Item N°Name:y1206HT Aluminum a-arm front lower l/hy1207HT Aluminum a-arm front lower r/hy1208HT Aluminum a-arm front uppery1209HT Aluminum front bulkhead Ay1210HT Aluminum front bulkhead By1036HT rose joints with conical spacersUnit prices: 249,00 EURPlease note: the hinge pins are not included, you will use the pins from the stock suspension!Suitable for Carson 1/6 (Comanche, Attack Evo, CRT + CPT) and Smartech Monster Truck.Price for the parts bought separately: 253,30 EURIntroductory price: 179,90 EUR / set

€249.00*

y1303/04 T male to EC5 female

Adapter cable T male to EC5 female.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

y1303/06 TRX female to T-connector

Genuine HT spare/option part.Adapter TRX female (Traxxas batteries) to T-connector.Adapter cable for the LiPo receiver battery in model Traxxas Xmaxx.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

This product is no longer available.

y1303/12 EC8 female connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected socket with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm bullet connectors found on many larger brushless motors.Contents:1 piece

€5.90*

y1303/08 EC5 charging cable

Genuine HT spare/option part.Charging cable for batteries with ES5 connector, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€12.90*

y1303/15 XT60 Charging cable

Genuine HT spare/option part.Charging cable for batteries with XT60 connector, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€8.90*

y1303/07 Balancer adapter cable

Genuine HT spare/option part.Adapter cable for connecting 2S batteries with EH-balancer connector (i.e. LiFePo receiver batteries y0664 and FG 6549) to chargers with XH-terminal (i.e. Imax or Team Orion).Without connection to the balancer Lithium batteries are usually not recognized by the chargers and accordingly also not charged.Content:1 piece

€3.90*

y1303/09 EC5 connector, male

Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

y1303/03 EC3 male to EC5 female

Adapter cable EC3 male to EC5 female.Dimensions:Length cable: 40 mmTotal length: 75 mmContent:1 piece

€9.90*

This product is no longer available.

y1303/20 HXT4 charging cable

Genuine HT spare/option part.Charging cable for batteries with HXT4 connector, length approx. 37 cm, silicone insulated cable with gold-plated connectors. Content:1 piece

€8.90*