53 products found for "y1106"

Catalogue #1

y1106 Aluminum ball joints with 5mm/M8 r/h or l/h thread, pair

Genuine HT spare/option part. Two balljoints 5mm/M8 optionally with four conical spacers, to replace FG #6029/1 + #6029/8 + balls. (Set content like FG 4437)The maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Dimensions:A = 5 mmB = M8 right/leftC = 8 mmD = 17,5 mmE = 39 mmContents:2 piece

€14.90*

Configure now

y1104 Maintenance tray for 1/5 cars

Genuine HT spare/option part. Maintenance tray for all 1/5 scale RC car models. The tray with its rubber pad prevents the car from sliding while working on the vehicle at the race or in the basement.Dimensions:Length: 370 mmHeight: 60 mmWidth: 170 mmContents:1 piece

€44.90*

y1107 Steel balljoints 5mm/M8, with conical spacers

Genuine HT spare/option part. Two balljoints 5mm/M8 with four conical spacers, to replace FG #6029/1 + balls (Set content like FG 4429/1).Fits almost for all 1/5 and 1/6 scale cars.The maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Contents:2 pieces

€14.90*

y1016 Zenoah G320RC with Walbro carburetor WT1107

With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€307.85*

y1105 Exhaust port and carburetor intake cover plates, for most usual 23cc - 30cc engines

Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm

€4.90*

Servo disk Multiplex Rhino, y1136, 1 pce.

5 mm thick servo disk with reinforcement ring around the spline, 40 mm diameter.All holes with 2.5 mm diameterHole circles: 20/21/22/23/30/31/32/33 mm

€1.90*

Bergyogi Double DVD DTM Racing Germany, y1126

Detailed report from the German Championship 2008 with additional videos from the 2007 finals.(DVD-video, system: PAL, region code free, run time: approx. 243 minutes, sound: MPEG-stereo, German language commentary)

€13.85* €27.70* (50% saved)

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

This product is currently not available.

Gear set for Smartech, Mega Evo, Mega Evo Pro Servos, y1166

Complete replacement gear set with ball bearings.

€24.90*

Mecatech brake line 2.7x4 for Expert / Crosshydro, y1176, 1 m

Brake line 2.7 x 4 mm, especially for Mecatech Expert and Crosshydro brakes.

€5.90*

y1103 Body support

y1103 Size: y1103/01 - Small

Genuine HT spare/option part. You can select from two different sizes of body support.Dimensions small body support y1103/01:Length: approx. 80 mmWidth: approx. 16 mmDistance bore to bore: approx. 64 mmDimensions large body support y1103/02:Length: approx. 105 mmWidth: approx. 16 mmDistance bore to bore: approx. 88 mmBore diameter: approx. 8 mmContents:2 pieces

€7.90*

y1101 Servo horn mounting screws, 10 pcs

y1101 Application: y1101/04 Mega Power-Servo, metal gears

Item N° y1101 Servo horn mounting screws, 10 pcsReplacement screws for mounting the servo horn on the servo shaft.Part is delivered in silver or black color from vendor!Choises:y1101/01Fit:Multiplex Jumbo and Power MCFG 6598 Savöx-Servo SC-0251MGFG 6599 Savöx-Servo SC-1256TG Measures: M3 x 8 mmy1101/02Fit:Multiplex RhinoHitec 805 MGHitec 9805 MGFutaba S3152 Measures: M2,5 x 10 mm Torxy1101/03Fit:Futaba und Robbe diverse ServosPlease check the required dimensions! Measures: M2,5 x 6 mm Torxy1101/04Fit:402115 Mega Power-Servo, metal gears Measures: M3 x 10 mm y1101/05Fit:Ace DS1015 Super Torque Digital Servo, y1051 Measures: M3 x 10 mm

€2.00*

y1104/01 Foldable maintenance tray for 1/5 and 1/6 cars

Genuine HT spare/option part. Foldable maintenance tray, ideal for 1/5 and 1/6 cars; even for heavy weight and high ground clearence cars like a Losi 5ive-T!Size folded:Width: 300 mmHeight: 315 mmDepth: 40 mmWeight 1 kgSize erected: Width: 300 mmHeight: 220 mmDepth: 210 mmContents:1 piece

€19.90*

1106 FG Alloy front riser blocks truck Evo 08-14

Genuine FG spare/option part. for Evo 08-14 with the newer front axle.Is needed to compensate for the larger diameter of the truck wheels.Dimensions:Length: 86 mmheight: 8 mmwidth: 8 mmContents:2 pieces

€19.95*

2009-04 Cask shaped springs for Mecatech Klick-Shocks, yellow 2,8 mm

These cask shaped springs are especially designed to fit the diameters of Mecatech Klick-Shocks and Mecatech Big Bore shocks.Dimensions:Inner diameter, upper: 20,5 mmInner diameter, lower: 16,5 mmOutside diameter: 29,5 mmLength: 49,5 mmWire diameter: 2,8 mm

€16.90*

TT1106 Top Tuning Motor cooling for FG brushless cars, long version.

Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Long fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware

€44.90*

110678 HPI Baja 5B-1 Buggy painted body, matte black

Genuine HPI spare/option part. Refresh the look of your Baja buggy with this easily installed, pre-painted bodyshell. This fully detailed bodyshell is pre-cut for instant and easy installation, so it's ready to fit on any Baja 5B, Baja SS or Baja 2.0 buggy.Also includes a matching decal sheet for the rear wing.HPI pre-painted bodies feature:Premium vinyl decals includedHigh quality polycarbonate for extra strength and long lifePre-drilled body post holes make mounting the body quick and simpleContents:1 set

€169.99*

This product is currently not available.