9 products found for "y0928"

rc-car-online - Home

HT Aluminum differential case conversion kit Carson Gas/Hell Devil/CRT 4x4/Thunderbolt, y0928, set

Alloy case conversion kit for Carson Gas Devil 4x4 (Smartech Titan) only, can be used for all differentials.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.

€89.90*

y0938 HT Replacement lever for y0932

Genuine HT spare/option part.Each one lever inklusive M3 x 10 mm screws. Spare part for y0932.Contents:1 piece

€27.90*

Receiver switch, Multiplex connectors old, y0920 - 1pce.

Old version Multiplex type connectors for both battery and receiver.

€10.10*

Adapter cable, high current / universal, y0922 - 1pce.

High current connector for the battery and Futaba / universal connector for the receiver.

€7.20*

y0929 HT Aluminum limited slip differential conversion kit for Carson Gas Devil + CRT 4x4, Conrad Hell Devil, Smartech Titan

Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece

€129.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/02 - 300 mm+ 1EUR

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

Variants from €5.90*

€6.90*

y0908 Rebuilt kit original Losi 5ive-T

y0908_04_021 Version: y0908/021 23 cm³ Rebuilt kit original Losi

Cylinder-piston repair kit for 23 cm³ or 26 cm³ Losi 5ive-T engine. The set includes the following parts:Cylinderpistonpiston ringcylinder foot gasketpiston pin clipPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer

€69.90*

y0968 HT-Steel pinion 34 teeth Speedgear for Carson / Smartech 4WD cars

Genuine HT spare/option part. Nitrited steel spur gear, profile regraded, for combination with the stock 43T spur gear which goes on the clutch bell. This gives a numerically lower drive ratio and makes it possible to use standard diameter buggy tires on this car!Attention: The speedgear has the same diameter as the stock 37T gear and is therefore not compatible with the other 37T/40T HT tuning gears!Speedgear 34T: I=7,74Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter.Contents:1 piece

€44.90*

ARA310928 ARRMA Aluminum Wheel Hex 24mm red for Kraton / Outcast 8S

Genuine ARRMA spare/option part. Contents:2 pieces

€19.99*